Se você não tiver uma conta na Biblioteca de Mídia da 2N, preencha o formulário de registro on-line e solicite o acesso.
Observe que o acesso à Biblioteca de mídia é exclusivo para representantes autorizados dos parceiros comerciais da 2N. Portanto, sua solicitação será analisada e aprovada pela 2N.
Se você está procurando um catálogo detalhando nossas soluções de sistema de intercomunicação de apartamento ou deseja uma folha de dados para o estilo IP 2N, tudo está abaixo. Pesquise, encontre, baixe, compartilhe!
Added functionality ‘Push to talk’ when Lift8 Fireman station activated (Lift8-1271)
Possibility to select behavior when concurrent alarm call activated on cabin units connected to one central unit, either queuing or connecting to conference according to new parameter 968 (Lift8-1690)
Possibility to mute microphone in cabin unit by DTMF signaling ‘9’ to make possible voice connection to the place with very high level of noise. End of muting again by sending DTMF signal ‘9’ Lift8-1699
Security improvements
New version of Mbed TLS 4.1.0 applicated (Lift8-1691)
New version of LittleFS 2.11.3 applicated (Lift8-1679)
Displaying of SMS with sensitive information in log is no more active (Lift8-1711)
Bugfixes
Unwanted permanent connection between fireman unit and machine room unit when installed in one shaft (Lift8-1472)
Logging time of NTP synchronization uses time after synchronization instead of actual time when synchronization was initiated (Lift8-1656)
Maximal length of service password set using service tool is 15 characters, correct value is 16 characters max. (LIFT8-1655)
Interrupted connection between 4G data and Ethernet port configured as internal data connection, reconnection of Ethernet cable needed (Lift8-1348)
Issue with operational call and checking call with DTMF inband communication (Lift8-1535)
SIP call using TCP direct call can’t be executed, P2P solution using TCP is not available – only UTP works correctly for connection without SIP proxy (Lift8-1661, Lift8-1664)
Time for checking call is changeable +- 10 minutes although NTP service works correctly (Lift8-1662)
Blocked log of central unit followed by restart (Lift8-1665)
Incorrect audio test of cabin unit on HW v.4 (Lift8-57)
When PIN on SIM in LTE module is changed, needed restart of the module is performed after timeout. Correct behavior is immediate restart (Lift8-685)
Repeated use of incorrect PIN for SIM in LTE module can result in SIM blocking. Now only one try of use incorrect PIN performed (Lift8-763)
Sporadic error in measured value of battery voltage (Lift8-821)
When MBN profile in LTE module is changed, restart of module must be performed (Lift8-1705)
Attempt for concurrent connection to central unit by USB and IP result in error of service tool (Lift8-323)
Displaying of ICCID in service tool without last digit fixed (Lift8-1261)
Communication error on serial line to LTE module resulting in occasional loss of character fixed (Lift8-1677)
SMS command for restart L8 RST password doesn’t result in restart of central unit (Lift8-1710)
Installation of service tool on new PC was problematic because of incorrect setting of installation process (Lift8-1718)
Incorrect message in evacuation mode for Italian language (Lift8-1230)
Restart of central unit fails when activated by change parameter 998 from 0 to 1 (Lift8-1714)
Operational call doesn’t work until checking call activated at least once (Lift8-1715)
Lift8 – Password management changed according to RED/CRA (LIFT8-1590)
Lift8 – Change in SMS password, not only numeric, command PWD for keyword change added (LIFT8-1594)
Lift8 – Forced change of service password for service tool, SMS and voice menu setting (LIFT8-1597, 1598)
Lift8 – Default time after switch on is set to first of February 2026 (LIFT8-1606)
Service tool – Added hint describing, that SIP phone number must have prefix ‘sip’ (LIFT8-941)
Service tool – Change in password menu place to menu ‘Device’ (LIFT8-1595)
Service tool – Change in numbering of parameters, setting of service password from 991 to 891 (LIFT8-1596)
Service tool – Added menu for rescue mode configuration - enabling and password (LIFT8-1599)
Service tool – Change of maximal length of strings in configuration according to needed values (LIFT8-1605)
Service tool – SIP registration time limits set to 60 – 3600s to avoid setting of too short values resulting in wrong functionality, setting 0 results in 300s (default value)(LIFT8-1616, 555)
Service tool – format validation of phone numbers for notification events (LIFT8-1622)
Security improvements
Lift8 – scan product for known open source vulnerabilities and address issues according to the Axis Vulnerability Management Policy (LIFT8-1444)
Lift8 – SBOM delivered for every release (LIFT8-1444)
Lift8 – Secure communication with device during configuration (LIFT8-1467)
Lift8 – Change in setting of passwords, demanded change of admin password and service password prior any changes (LIFT8-1515)
Lift8 – After setting wrong password 3 times, the device is blocked for password input for defined time (LIFT8-1581)
Bugfixes
Lift8 - RS232 module – AT command issue resulting in device restart (LIFT8-1485)
Lift8 - Error in planned checking call (LIFT8-1573)
Lift8 - SIP call over TCP protocol can’t be realized (LIFT8-1608)
Lift8 – Date can’t be set using phone call (LIFT8-179)
Lift8 – Issue with combination of wireless data connection and LAN connection (LIFT8-616)
Lift8 – Direct call to IP address doesn’t work when TCP protocol used (LIFT8-1563)
Lift8 – issues with quality of reproduced sound in announcements (LIFT8-1301)
Lift8 – When password for rescue mode end demanded, control of password parameter provided (LIFT8-1493)
Lift8 – Combination of FW upgrade in progress and sending event SMS results in unsuccessful upgrade (LIFT8-1549)
Lift8 - Invalid length of service password sent by SMS results in device reset (LIFT8-1610)
Lift8 – Setting of date to invalid value can result in need to perform firmware upgrade (LIFT8-179)
Lift8 – Sending SMS event without response results in LTE module reset (LIFT8-1620)
Service tool – Event configuration issue when configuration loaded from device, it can’t be loaded back (LIft8-1614)
Service tool – For some new functionalities missing translation to other languages than English, fixed (LIFT8-1430, 1572)
Service tool – issue with blocking tool when invalid date set, added checking of tine in device after setting (LIFT8-1532)
Service tool – When device connected by TCP, change in language od service tool results in device restart (LIFT8-1623)
Version: 3.1.4
Final version: 3.1.4.0.1
Date: 26.11.2025
New features and improvements
Lift8 – TCP signaling for SIP connection added – both TCP and UDP available (LIFT8-1041)
Lift8 – camera functionality is not supported for FW versions 3.x both for new and old version of hardware (LIFT8-1560)
Lift8 – User Agent field filled with actual device or application (LIFT8-1043)
Communicator – signaling of data communication error added (LIFT8-1495)
Lift8 server – repeated question whether configuration files should be deleted to avoid unwanted deleting of application data (LIFT8-1476)
Security improvements
Lift8 – conformity with standard EMN 18031 approved (LIFT8-1091)
Lift8 – conformity with standard EN 303 645 approved (LIFT8-1139)
Bugfixes
Lift8 – unreliable upgrade of LTE module fixed (LIFT8-1415)
Lift8 – identification of used audio unit by SIP call in evacuation mode (LIFT8-1420, LIFT8-1426)
Lift8 – repeated attempt to SIP registration although the data connection is not available (LIFT8-753)
Lift8 – incorrect functionality of machine room unit when invert of Alarm input applicated (LIFT8-1247)
Lift8 – audio unit Compact can be used in cabin only – changed to any position (LIFT8-1502)
Lift8 – audio quality in call improved, disturbance in call and in reproduced sounds fixed (LIFT8-1418, LIFT8-1301)
Lift8 LTE – added MBN profile for Vodafone (LIFT8-1519)
Service tool – user message can’t be deleted during playback, delete function blocked. Improved loading user message (LIFT8-1380, LIFT8-1386)
Version: 3.0.0 – Hardware version 4 support
Final version: 3.0.0.0.8
Date: 15.10.2025
New features and improvements
Lift8 – Reporting of battery capacity for one hour of operation according to EN 81-28 (LIFT8-1275)
Lift8 – forced test alarm set by default to 30s to fulfill demand of EN 81-28 by default (LIFT8-1407)
Lift8 – Ethernet port placed on base board of L8 HW version 4, no additional Ethernet board needed (LIFT8-950)
Lift8 – USB C port supported on base board of L8 HW version 4, instead of previous USB B (LIFT8-988)
Lift8 – Change in battery and power source voltage displaying – two separated values (LIFT8-456)
Lift8 – Improved signalization of data connection status by LED (LIFT8-13290)
Lift8, Communicator – Unification of user agent reporting with other 2N products (LIFT8-1043, LIFT8-1044)
Lift8, Communicator – Possibility to confirm checking call by connecting the call without any additional confirmation (LIFT8-1257)
Lift8 LTE – Possibility to select MBN profile for LTE module, needed for VoLTE support for some operators, profiles added to upgrade packets (LIFT8-1282, LIFT-1284, LIFT8-1285)
Control panel – Reporting extended by possibility to report time and date of last successful call (LIFT8-1258)
Control panel – When the interval for checking call is set to 72 hour (default value – 3 days), the interval 74 hour is accepted, error is reported after this time (LIFT8-904, LIFT8-1385)
Control panel – separated upgrade for LTE module and FW in Lift8 to prevent problems when upgrade is done in one step over wireless connection (LIFT8-1401)
Communicator – Change of map used for localization of installation, instead of BingMaps used OpenStreetMaps because of licensing issue (LIFT8-1288)
Communicator – Improved reporting checking call by adding information about results (LIFT8-1391)
Security improvements
Lift8 - Trust zone supported for HW version 4, secure memory area to save information, which should be kept private (LIFT8-960)
Lift8 – Secure boot supported for HW version 4, verified FW loading protected against use of unauthorized firmware (LIFT8-1019, LIFT8-1116)
Lift8 – Verification of authenticity and integrity of firmware for update (LIFT8-1156, LIFT8-1157)
Lift8 - Cryptography protection of personal data transiting between device and associated services (LIFT8-1187)
Lift8 - Libraries of third party upgraded to latest versions (LittleFS, LWIP, TLS…) (LIFT8-1208, LIFT8-1262, LIFT8-1264, LIFT8-1313)
Lift8 – Tamper added for HW version 4, possibility to report opening of the case (LIFT8-999, LIFT8-989, LIFT8-1029)
Lift8 – Mechanism against unauthorized authentication by repeated access looking for and and keyword by blocking interface (LIFT8-1144)
Lift8 – Protection against unauthorized debug processing (LIFT8-1179)
Lift8 – Protecting user data by replacing after factory reset (LIFT8-1194, LIFT8-1195, LIFT8-1196)
Lift8 LTE - New SDK for LTE module used – RED compliant (Lift8-1346)
Bugfixes
Lift8 – Lost IP connection when static IP address set – fixed (LIFT8-1090)
Lift8 – Incorrect LED signalization when connection in roaming active (LIFT8-816, LIFT8-1078)
Lift8 – Restart activated by SIP service by call is delayed for 2-3 minutes – fixed (LIFT8-1287, LIFT8-1292, LIFT8-1408)
Lift8 – Error in invite by SIP call, missing TAG fixed (LIFT8-1278, LIFT8-1399)
Lift8 – Default value for forced call changed to 30s to allow initialization of forced call according EN 81-28 in default setting (LIFT8-1388)
Lift8 LTE – Upgrade of module failed because of memory shortage – fixed (LIFT8-1333)
Version: 2.9.2 – Bugfix version
Final version: 2.9.2.0.5
Date: 17.3.2025
New features and improvements
Lift8 – Functionality of machine room communicator according EN 81-72, activation of microphone by button demanded (LIFT8-1014)
Lift8 LTE – possibility to set preferred DNS 1 and 2 added (LIFT8-1079)
Bugfixes
Lift8 – reporting identification od calling location in higher detail (LIFT8-449)
Lift8 LTE – long time period for SIM logging for some operators – fixed by longer timeout for critical operations (LIFT8-1081)
Control panel – Notification of license expiration of Lift8 server added, correct message when license expired displayed, login with expired license allowed with limited functionality (LIFT8-576, LIFT8-847, LIFT8-849, LIFT8-568, LIFT8-1232)
Communicator – limits for setting of port numbers replaced (LIFT8-523)
Lift8 server – Expiration of license correctly reported (LIFT8-868, LIFT8-1034)
Version: 2.9.0 – Evacuation scenario support, control center capacity increase
Final version: 2.9.0.0.2
Date: 6.12.2024
New features and improvements
Lift8 – evacuation mode available, up to 64 communication units, driven from connected IP phone – see manual for details (LIFT8-931, LIFT8-932, LIFT8-933, LIFT8-934, LIFT8-946, LIFT8-949, LIFT8-953, LIFT8-1036)
Lift8 – support of two Fireman units in one shaft available (LIFT8-1013)
Lift8 LTE – possibility to set PAP, CHAP authorization for wireless connection added (LIFT8-1052)
Control panel – counter of control and alarm call added (Lift8-776, Lift8-1038)
Lift8 server, communicator, control panel – improvements to increase number of connected devices up to 5000 units with keeping acceptable response for demanded operations (Lift8-350, Lift8-839, Lift8-865, Lift8-908)
Lift8 Control panel, Communicator – listing of information organized by groups in alphabetic order instead of time of recording – better orientation in listings (LIFT8-524)
Bugfixes
Control panel – increased number of control calls and reports to be registered to support traffic for higher number of connected devices (Lift8-882, Lift8-883).
Communicator – global map functionality switched off because of issues with map source and wrong function of displaying for 100+ points in map. Plam to solve this issue in future (LIFT8-843, LIFT8-1032).
Communicator – acceptation of identification number for incoming call with prefix * to be able to accept signaling from some SIP connection providers (LIFT8-708).
Communicator, Lift8 server – high number of registered control calls and alarm calls (about 50 000+) resulted into Lift8 server crash when higher amount of incoming calls occur concurrently (Lift8-883)
Version: 2.8.7 – 100 Mb LAN connection
Final version: 2.8.7.33.33
Date: 24.4.2024
New features and improvements
Lift8 – support for LAN communication board 100 Mb added (LIFT8-595, LIFT8-631)
Lift8 – second DNS server setting available (LIFT8-647, LIFT8-665)
Service tool - configurable space between DTMF tones during configuration to allow setting when issues with DTMF transmitting occur (LIFT8-677)
Service tool – changed provider of map source (LIFT8-734, LIFT8-701)
LiftIP1 – Incoming call by default configuration, ability to switch to voice menu by DTMF 9 (LIFT8-155)
Bugfixes
Lift8 – incorrect message about end of button stuck error when alarm activated – fixed (LIFT8-640, LIFT8-327)
Lift8 – error of wireless module registration fixed (LIFT8-745)
Lift8 LTE – MBN profile activation check after restart – improved reliability of VoLTE calls (LIFT8-676)
Lift8 LTE – upgrade of central unit blocked when SIM with PIN inserted and incorrect PIN set in Lift8 (LIFT8-667)
Lift8 LTE – change of SIP availability according to 2G/4G technology changes (LIFT8-675, LIFT8-753)
LIFT8 LTE – when LTE module inserted, upgrade from older versions which doesn’t support LTE module is not possible - fixed (LIFT8-683)
LIFT8 LTE – module restart after VoLTE activation on SIM – necessary for VoLTE activation (LIFT8-754)
Service tool – configuration blocked during loading to prevent data damage (LIFT8-662)
Service tool – visualization of line speed for LAN corrected after connecting device, no restart of lift8 needed (LIFT8-723)
Service tool – unsuccessful FW upgrade with LTE module thru USB (LIFT8-791)
Service tool – compatibility of different versions of service tool and L8-server allowed (LIFT8-569)
L8-Server – incorrect setting if SIP domain – used parameter from SIP server (LIFT8-795, LIF8-798)
L8-Server – incorrect length of CLIP (less then minimal length 5 digits) results in server restart – fixed (LIFT8-680)
Version: 2.8.5 – LTE support
Final version: 2.8.5.33.28
Date: 27.11.2023
New features and improvements
Lift8 - France language added to voice menu (LIFT8-527)
Lift8 – Support for LTE module integration and communication (LIFT8-110), (LIFT8-111), (LIFT8-112), (LIFT8-116), (LIFT8-121), (LIFT8-130), (LIFT8-137), (LIFT8-138), (LIFT8-140), (LIFT8-374)
Lift8 – SIP call using LTE module and wireless data connection implemented, direction of call defined by prefix (LIFT8-123), (LIFT8-124), (LIFT8-125), (LIFT8-114), (LIFT8-128), (LIFT8-134), (LIFT8-553), (LIFT8-634)
Lift8 – VoLTE call support using LTE module (LIFT8-117)
Lift8 – SMS services added to support LTE module (LIFT8-444)
Lift8 – Data connection support for LTE module (LIFT8-122)
Lift8 – Firmware in LTE module upgrade support (LIFT8-136)
Lift8 – LED functionality changed to support new features connected with LTE module use, description of new functionality in user manual (LIFT8-591)
Lift8 – Compressing of log files configured, block compressed when size 10MB reached (LIFT8-528)
Lift8 – Reporting of LTE module FW version, both the application FW and module FW, adding to log (LIFT8-582), (LIFT8-587)
Lift8 – Restart of LTE module when the malfunction detected, including logging of this situation with details allowing troubleshooting (LIFT8-108)
Service tool – SIP and VoLTE status visualization when LTE module assembled (LIFT8-435), (LIFT8-543)
Service tool – Reset for I/O module added to set default settings (LIFT8-359)
L8-Server – Repeating unsuccessful registration attempt till restart of application fixed (LIFT8-337)
Bugfixes
Lift8 - Change in checking call DTMF timing, unwanted space fixed (LIFT8-445)
Lift8 – Incorrect DTMF signaling during alarm call fixed, timing of signals for call end changed (LIFT8-446)
Lift8 – Watchdog for SIP connection on Ethernet port added, restart of SIP engine when registration failed (LIFT8-424), (LIFT8-309)
Lift8 – Day of week for checking call functionality fixed (LIFT8-251)
Lift8 – Default time setting from programming tool by DTMF fixed (LIFT8-333)
Lift8 – Parameter ‘day of week’ (986) shifted, beginning of week now Monay (LIFT8-325)
Lift8 – Default battery expiration time changed from 3 years to 2 years, according standards (LIFT8-632)
Lift8 – When PIN for SIM is filled with incorrect value, the PIN is after restart repeated till SIM blocked and PUK needed, now blocking of SIM avoided and wrong PIN indicated by LED (LIFT8-635)
Service tool – Beep notification of I/O module, input and output divided (LIFT8-330)
Service tool – Popup notification of I/O module status can result in application crash, fixed (LIFT8-425)
Service tool – Filtering of connection status fixed (LIFT8-464)
Service tool – Connection attempt during device factory reset results in impossibility of later connection, fixed (LIFT8-439)
Communicator – error in compatibility of database resulting to impossibility to save time setting fixed (LIFT8-511)
Communicator – change in PJSIP licensing done because of different mode of use (LIFT8-418)
Communicator - License politics error fixed, real status of license displayed (LIFT8-522)
Control panel – Incorrect export of Operational Calls report – format error fixed (LIFT8-410), (LIFT8-411)
Control panel – Export of alarm call identification file corrected (LIFT8-430)
Control panel – Incorrect way for new group creation by superuser in another group fixed (LIFT8-381)
Control panel – License politics error fixed, group licenses working after expiration (LIFT8-520), (LIFT8-517), (LIFT8-518)
Control panel – Communication with Lift8 during the call may result in application crash, fixed (LIFT8-611)
Graphic of tools – Resolution of application window setting changed (LIFT8-513)
All tools – After replacing from computer some empty directories resists, fixed (LIFT8-536)
Whole system – 2N logo changed (LIFT8-419)
Version: 2.8.4 - Schmitt
Final version: 2.8.4.33.21
Date: 15.5.2023
New features and improvements
Change in licensing – control of connected devices, whether the amount agrees with license, timing of trial time period improved (LIFT8-438), (LIFT-486)
E-mail notification of exceeding number of licenses added (LIFT8-488)
Bugfixes
Fixed errors in German translation for service tool (LIFT8-458)
Lift8 - Voice menu for Latin America (Spain) added (LIFT8-366)
Service tool – Fixed position of parameter groups, independently on languages (LIFT8-375)
L8 server - Support of LiftIP2 on Lift8 server (LIFT8-326)
Communicator - Dual audio output added – different audio output can be set for ringing and for call, improved management of connected audio devices (LIFT8-396)
Control Panel – Increased maximal length of intercom name from 15 to 49 characters
Control Panel – Specific response (Custom) to Lift8 to confirm Checking call, Alarm call and Call to Lift8 added (LIFT8-393, LIFT8-394)
Bugfixes
Fixed translation in tool texts and hints (LIFT8-373, LIFT8-200, LIFT8-372)
Fixed issues in manuals and in references to manual in tools (LIFT8-334, LIFT8-335)
Lift8, LiftIP – Support of SIP proxy registration after change in Netstar (LIFT8-391, LIFT8-405)
Service tool - Wrong functionality of calendar, when month changed, day of weeks stays from last month (LIFT8-328)
LiftIP – Checking call timeout can result to incorrect end of call when registration during the waiting changes (LIFT8-403)
LiftIP – Finding in logs improved, wrong function of help fixed (LIFT8-245)
Service tool - Selection of connection in service tool for LiftIP selects more than one connection (LIFT8-361)
Service tool – Hidden keyword for parameter 1122 – keyword for RTSP connection to camera in service tool (LIFT8-305)
Service tool – Improved search in logs, now is case sensitive (LIFT8-371)
Service tool – Graphical view to configuration fixed (LIFT8-380)
L8 Server – MapQuest API service change supported to keep map functionality unchanged (LIFT8-388)
L8 Server – Setting detail of server fixed (LIFT8-515)
Communicator - During incoming call to Communicator, the map is not visible (LIFT8-347)
Communicator – Wrong position of intercom position on map, when windows size changed, improved accuracy of position (LIFT8-316, LIFT8-329, LIFT8-360)
Communicator – Incorrect setting of audio device for input and output (LIFT8-397)
Communicator – Incorrect displaying of names of audio devices – 32 characters only (LIFT8-398)
Communicator – Adding new Lift8 fails in specific circumstances (LIFT8-401)
Control Panel - List of intercoms in Control panel doesn’t show added intercom before refresh, not full view to all intercoms as admin without selected group of intercom (LIFT8-356)
Control Panel - Configuration of maps available to prevent issues connected with end of service MapQuest (LIFT8-363)
Control Panel - Fixed error in setting of test E-mail (LIFT8-302)
Control Panel – CPC Antenna 2N Extension support bug fixed (LIFT8-315)
Control Panel – Specific response to Lift8 to confirm Checking call, Alarm call and Call to Lift8 fixed (LIFT8-393, LIFT8-394)
Control Panel – ID extraction from CPC Antenna 2N ext. protocol fixed (LIFT8-357)
Control Panel – Export of alarm call has missing information about Agent, when the value is Server (LIFT8-343)
Control Panel – Export of call from intercom detail shows only test call (LIFT8-407)
Version: 2.8.3
Final version: 2.8.3.33.14
Date: 28.6.2022
New features and improvements
Lift8 – Identification of lift shaft in alarm call by voice message. (Lift8-25)
Lift8 – Alarm button self-test added, special type of alarm button needed. (Lift8-27, LIFT8-209)
Lift8 – Italian voice menu added. (LIFT8-31)
Lift8 – Polish voice menu added. (LIFT8-185)
Lift8 - Possibility to set siren output on the machine room communicator when alarm call activated. (LIFT8-33)
Lift8 - Information E-mail from alarm call to Control Panel (additional functionality to E-mail notification about checking call). (LIFT8-12)
LiftIP – Italian voice menu added. (LIFT8-32)
All tools - GUI of Lift8 supports seven languages: CZE, ENG, ESP, GER, FRA, ITA, RU. (LIFT8-6)
Communicator - Plan or map of the area with marked locality of lift is visible during emergency call. (LIFT8-7)
Communicator - Possibility to set keyboard shortcuts for define actions in Communicator to allow use of keyboard emulator. (LIFT8-20)
Communicator – Test of microphone connection added. (Lift8-189)
Bugfixes
Installation - Missing DLL libraries when Lift8 tools installed, mostly connected with Win10. (LIFT8-59, LIFT8-89)
Lift8 - Time overflow error – when Lift8 runs 49,7 days, timer overflow can result into unexpected irregularities in function. (LIFT8-36)
Lift8 – Alarm call with CPC Antena support failed in intercom identification – first number lost. (LIFT8-197)
Lift8 - Time synchronization by SNTP on by default – log with correct timing supported. (LIFT8-56)
LiftIP – issue with Payload Type for DTMF. (LIFT8-159, LIFT8-19)
LiftIP – communication issue with AVAYA – too long packets. (LIFT8-42)
LiftIP – After change of configuration confirmed by password, wrong password reported. (LIFT8-254)
Service tool - doesn’t correctly display all parameters depending on screen resolution. (LIFT8-52, LIFT8-147)
Service tool – incorrect filter, only numbers applied. (LIFT8-257)
Service tool – Device info error when older device connected because of missing hwinfo. (LIFT8-249)
L8 Server - Special characters for example - !@#$% - can’t be used as part of the SIP password. (LIFT8-10)
L8 Server -after change of IP address on connected PC registration failure occur. (LIFT8-90)
L8 Server – Error occur when E-mail report sent to three or more address. (Lift8-344)
L8 Server – Empty E-mail address for notification results into application lock or sending error. (LIFT8-247, LIFT8-301)
Communicator - Deleting of Control panel user, who is registered in Communicator results In lock of the application. (LIFT8-24)
Communicator - crash when display resolution changes. (Lift8-146)
Communicator - direct call user is not correctly signed off after user delete performed. (LIFT8-148)
Communicator - doesn’t allow moving of map by scrollbar. (LIFT8-171)
Communicator – when size of map changed, the change is not permanent. (LIFT8-252)
Communicator - crash when display resolution changes. (Lift8-146)
Communicator - direct call user is not correctly signed off after user delete performed.
Communicator - doesn’t allow moving of map by scrollbar. (LIFT8-171)
Communicator – when size of map changed, the change is not permanent. (LIFT8-252)
Communicator - doesn’t allow moving of map by scrollbar. (LIFT8-171)
Communicator – when size of map changed, the change is not permanent. (LIFT8-252)
Communicator - doesn’t allow moving of map by scrollbar. (LIFT8-171)
Communicator – when size of map changed, the change is not permanent. (LIFT8-252)
Communicator – When filtering by length of call or agent used, application crashes. (LIFT8-313)
Control panel - When Call server is set, correct visualization of all details in graphics is not guaranteed. (LIFT8-47)
Control panel – forced save of storage setting before next step can be performed. (LIFT8-158)
Control panel – When more intercoms on one plan placed, it is not possible to remove any of them. (LIFT8-217)
Control Panel – Test of storge availability, if lost, warning generated. (LIFT8-223)
Control Panel – searching of intercom by address in map failed. (LIFT8-92)
Functionality ‘Fireman’ allows to use connected IP device as fireman communicator in lift, using SIP server in device (LIG2N-699)
Function to send message when batteries are going to be flat according to EN 81-28, necessary for TUV certification (LIG2N-715)
New version of wireless modules supporting with SDK used, security demand (LIG2N-745, 749, 750,
Restriction for SMS setting phone number can be applicated id demanded (LIG2N-783)
Default setting of wireless connection changed to roaming enable (LIG2N-753)
Added functionality needed for Open VPN certificate management – uploading, downloading, deleting (LIG2N-412)
Counter of LiftGate malfunction – resets because of module malfunction, LiftGate process crash, Daemon resets and user invoked reset (LIG2N-692, 693, 814)
When uploading of any file in progress, the selection menu is not displayed to avoid confusing of the user (LIG2N-769)
When battery disconnected, the information is displayed in Battery menu and parameters connected with battery are grey (LIG2N-755)
Adding parameters which can be set by SMS – parameters of DNS servers (LIG2N-780)
Defined format of configuration SMS – unification with EasyGate IP (LIG2N-826, 828)
Bugfixes:
High pulse load on DSL connection can generate disturbance on power source 48V resulting in block of PoE source - fixed (LIG2N-726)
When firmware upload is interrupted, the next upgrade can be performed only after device restart (LIG2N-582)
Damaged battery can be incorrectly detected, found zero capacity can induce zero dividing error resulting in wrong functionality (LIG2N-738)
Flooding log by error messages of Linux Avahi daemon (LIG2N-709)
Error in decoding of long SMS for configuration, now can be more commands sent in one SMS (LIG2N-756)
Protection against https certificate with incorrect format added (LIG2N-767)
Autometic change of IP address when connection thru WAN port changed, after reconnection is necessary to perform reset of device (LIG2N-459)
Incorrect signaling of battery capacity by LED Battery fixed (LIG2N-773)
Error with VoIP authentication (realm) fixed (LIG2N-816)
Version: 1.15.0
Final version: 1.15.0.0.4
Date of issue: 13.3.2025
New features and improvements:
Possibility to disable Ping service on LAN and WAN, default setting – disabled (LIG-631)
Open VPN supported on IPv6 (LIG-331)
Increased length of PIN for SIM, maximal length 8 digits (LIG-626)
Authorization PAP/CHAP added for wireless connection (LIG-649)
Multicast DNS ability (MDNS) added (LIG-697)
Configuration for comment during login to web interface according IEC-62443-4-2, CR 1.12 added (LIG-640)
Battery life time alert set to default value 730 days (LIG-509)
Bugfixes:
Battery management improvement, protection against overloading by comparing capacity and charge added (LIG-672, LIG-684, LIG-689)
Communication supported by VLAN between LAN port on central unit and WAN failed (LIG-703)
Redirecting router solicit message to LAN as multicast message to speed up connecting devices in LAN to WAN after switching connection to WAN (LAN-535)
Incorrect signaling of data connection after mobile network connection lost fixed (LIG-584, LIG-585, LIG-586)
Version: 1.14.0
Final version: 1.14.0.0.3
Date of issue: 25.10.2024
New features and improvements:
Specific configuration for Wurtec added (LIG-651)
Bridge mode for IPv.6 enabled in default configuration (LIG-656)
Battery low reporting improvement – both capacity and voltage considered (LIG-662)
Filtering of signal level messages in syslog – suppressing unimportant changes evidence to avoid syslog overload (LIG-665)
Measuring of battery internal resistance added for diagnostic purpose (EGL-943)
Decreased data consumption by deleted keep alive packets in EGIP application, only keep alive packed generated by tribble tunnel expected as sufficient (EGL-1058)
Bugfixes
Unexpected short disconnection from network fixed, issue connected with module status reporting (EGL-1378)
Invalid certificate issue, after longer disconnection is the certificate in EGIP invalid and the device can’t connect to Elevator center. Attempts to connect results in high data consumption (EGL-1347]
Version: 1.6.2
Final version: 1.6.2.0.3
Date of issue: 2.10.2025
Only version for EU issued
New features and improvements
Calling party ID (CLI), FSK according to standard ETS300659 implemented (EGL-594)
Possibility to define primary SIM slot (EGL-1211)
Small changes in positions in Web configuration menu (EGL-1212)
Adjustable number of unsuccessful pings to switch to secondary Ping server (EGL-1254)
Reporting of battery capacity for one hour of operation according to EN 81-28 (EGL-1221)
Possibility to switch off internal watchdogs activated by inaccessibility of data or by IMS not ready (no VoLTE available) (EGL-1222)
Security improvements
Configurable system notification before authentication according to IEC62443-4-2 CR 1.12 (EGL-1218)
New SDK with blocking for prohibited localities, downgrade to version without this property not allowed (versions 1.6.0 and lower) (EGL-1299, EGL-1300, EGL-1324)
Configuration interface accessible on WWAN port 8080 – risk when SIM with public IP address is used. Problem in version 1.6.1 only, fixed (EGL-1325)
Bugfixes
Unexpected restart during upgrade connected with low RAM capacity fixed (EGL-1304)
Unexpected sporadic memory leak fixed by memory capacity control (EGL-1256, EGL-1302, EGL-1304)
When PIN on SIM was activated, no IMSI and ICCID information displayed on configuration web in WWAN section – fixed (EGL-1279)
Issue with Busy tone when the outgoing call is refused fixed – connected with new SDK in version 1.6.2.0.2 only (EGL-1315)
Incoming call is refused when connected device picks up the call after first ring – fixed (EGL-1331)
Suppressed generation of not used event connected with temperature change without hysteresis to decrease volume of transmitted data (EGL-1334)
Version: 1.6.0.1.14
Final version: 1.6.0.1.14 – hotfix, not for production
Date of issue: 3.2.2026
New features and improvements
Decreased data consumption by deleted keep alive packets in EGIP application, only keep alive packed generated by tribble tunnel expected as sufficient (EGL-1058)
Bugfixes
Unexpected short disconnection from network fixed, issue connected with module status reporting (EGL-1378)
Invalid certificate issue, after longer disconnection is the certificate in EGIP invalid and the device can’t connect to Elevator center. Attempts to connect results in high data consumption (EGL-1347]
Suppressed generation of not used event connected with temperature change without hysteresis to decrease volume of transmitted data (EGL-1334, EGL-1381)
Version: 1.6.0
Final version: 1.6.0.1.13
Date of issue: 12.3.2025
New features and improvements
Added algorithm for watching IMS state. When the Gateway is connected to 4G network and IMS enabled is set (it means, that VoIP voice connection is demanded), the IMS state “Ready” is expected. When the ready state is lost, restart is performed after 10 minutes. When the IMS ready is not reached after restart, the restart is performed in one hour period till IMS ready state is reached. Restart is inhibited during upgrade and during network selection period including SIM change (EGL-1160)
Lift1 setting support – profile selection, Lift Id number by cloud (EGL-961, EGL-972)
Lift1 security improvement – change of default password by EGIP according to the user demands (EGL-929)
Menu for Lift1 support concentrated to one submenu (EGL-928, EGL-931, EGL-960)
Configuration of Lift1 by message sent from the web interface instead of SMS with the equivalent functionality (EGL-930)
VoLTE support for Vodafone global SIM – both with MCC+MNC 204+04 and 901+28 – proper MBN profile included in FW (EGL-974, EGL-976)
Module EC25-AFFA support – prepared for Verizon, certification necessary (EGL-555)
Change tone progress signaling – till connection to wireless network established, busy tone generated instead of dial tone (EGL-573)
Setting criteria for connection provider change for SIM with roaming to switch to different provider if preferred provider signal has poor quality (EGL-599)
Logging of special Quectel data log to allow remote diagnostic of Quectel/Qualcomm issues (EGL-617)
Setting of Lift1 profiles for profile numbers up to 19 (EGL-647, EGL-773)
Setting of parameter “user agent” (name of VoLTE client) added, default value “EGIP”. Needed for VoLTE connection in some networks (EGL-689)
Manual operator selection for test purposes added (EGL-703)
Software modem support (EGL-623)
Change oi default setting of DTMF in SIP, instead of inband in used RTP event as default setting (EGL-1037)
Default setting for SW modem on devices with SW modem support to Enable (EGL-1111)
IMS state reported to Elevator center by event to improve synchronization of data about IMS (EGL-1109)
Modem UART speed increased from 4800 bps to 9600 bps to improve longer files transmission (EGL-1067)
Change in SMS INF message – added information about FW version, IMEI, IMSI (EGL-1049)
User agent setting change for Australia – not set, value from MBN profile will be used – needed for VoLTE with Telstra (EGL-1082)
Function for MBN profiles actualization forced from internal or external MBN profile database, to be used after FW actualization or factory default setting automatically (EGL-1088)
VoLTE support for Vodafone global SIM in Germany – changes in Vodafone network, appropriate MBN profile added to EGIP. (EGL-789)
MBN database management by EC support in device (not yet in EC) (EGL-914)
Inversion of relay for failure status available, allow to signalize failure when battery empty and device in off state (EGL-769)
Set active CPC for US versions – standard method to signalize end of call in USA (EGL-1017)
Voice menu for Lift1 in all supported languages (EGL-1045)
Security improvements
Replacing of sensitive information from log – keyword for log to wireless network when used is now not visible in log, only information about presence of keyword available (EGL-721)
Denied access to login after three unsuccessful attempts for defined time window according to demand IEC 62443-4-2 CR1.11 (EGL-934)
Reduction of USB access to system services for security reason especially for using EGIP for IP conection (EGL-330, EGL-833, EGL-1020)
Bugfixes
Duplicity of MBN profiles resulted in VoLTE not active, fixed by replacing all profiles in module and loading new set of modules (EGL-1127)
When reinstall of MBN profiles is done with the same profiles as used ones, the following restart was inhibited with the result, that new MBN profile system was not activated – fixed (EGL-1146)
Failure in transmission of events, when communication channel interrupted and restored (EGL-1196)
Delay after FW upgrade in US version, the GW starts functionality after additional restart initiated by watchdog, fixed (EGL-1077, EGL-1085)
User agent setting according the configuration can be replaced by MBN profile to another value – fixed (EGL-1092)
Error in digital signature of MBN profiles in production fixed (EGL-1087, EGL-1078)
Demand of PIN or PUK signaling on web and by LED fixed (EGL-771)
Ping service was stopped after restart of data connection – fixed (EGL-772)
SIM state in menu Network/WWAN monitoring always “Unknown” – fixed (EGL-777)
Error of logging to network with PIN set on some SIM cards – typically in roaming – fixed (EGL-778)
Wrong comment for SMS/Digital input – By opening and by closing has opposite function. In English version only – fixed (EGL-715)
Error in SMS message INF by some combinations of parameters occur – fixed (EGL-718)
Lift 1 setting with wrong parameters refused, but connected Lift 1 still picked up by ring without setting followed – fixed (EGL-775)
Busy tone to FXS was generated when no voice channel available. Result – impossible modem connection in this state - fixed (EGL-814)
Modification of W-dog during process of operator selection to avoid repeated restart when selection takes longer time (EGL-819)
Ping function – server witch IP address was received first from DNS. Now used server in the order according to the list of servers for Ping function (EGL-813)
Factory reset and FW upgrade signaling – red LED only to be active (EGL-831)
Limit for battery voltage dependent on temperature and increasing limit voltage for loading to avoid incorrect error message overvoltage (EGL-812, EGL-941)
When the data connection thru modem during communication is interrupted, for example by disconnecting the analogue modem connected to FXS port, new attempt for data connection can fail – fixed (EGL-975)
Correcting of duplicities in SMS parameters (EGL-1007)
Data connection restored after interruption of physical connection on USB (EGL-1026)
After voice connection forced to 2G/3G because of fallback (VoLTE not supported) EGIP didn’t switch back to 4G although the network is preferred and available (EGL-1048)
Version: 1.5.0
Final version: 1.5.0.0.4
Date: 28.6.2022
New features and improvements
Change in modem to TCP connection allowing to set parameters for connection in bigger detail by parameters (EGL-679, EGL-677)
Change in serial line to TCP connection allowing to set parameters for connection in bigger detail by parameters (EGL-692, EGL-677)
Automatic setting of battery installation time when the device is installed (EGL-686, EGL-691)
Possibility to fix the length od DTMF tones when device connected by VoLTE and DTMF transmitted using RFC2833 (EGL-697)
It is not necessary to use transient version 1.4.0 to use version 1.5.0, it is possible to upgrade from any older version (EGL-698)
Change of factory default settings for key customers and generic version (EGL-702)
Security improvements
Modem and serial line to TCP connection doesn’t allow connection to internal IP address – 127.0.0.1 (localhost) and IP address assigned by mobile operator to the device to avoid unauthorized access (EGL-693)
Bugfixes
Signalization of expired batteries fixed in situation without connection to EC– when battery lifespan overstepped, the device signalized the situation by yellow color of LED Power (EGL-691)
Change of parameters of TCP connection when connection active resulted in internal error of EGIP – fixed (EGL-699)
Version: 1.4.0
Final version: 1.4.0.4.2
Date: 8.4.2022
Not for production
New features and improvements
Set of messages for unsuccessful upgrade enhanced for better diagnostics (EGL-616)
Security improvements
Unused tools and libraries in the filesystem replaced (EGL-409)
Improved protection of configuration files against decryption (EGL-423)
Digital signature of FW as protection against unauthorized FW (EGL-503)
Processes running with necessary privileges only (EGL-605)
Change of encryption algorithm RSA by AES to increase security level (EGL-648)
Bugfixes
VoLTE active even with IMS disabled (EGL-443)
Connecting to EC issue – incorrect time in AT&T network by NTP – solved by NTP off, time from wireless network used (EGL-468]
Web menu Status – visibility of LED submenu fixed (EGL-528)
Calibration constant for voltage measuring fixed in production and repair mechanism for already issued products added to FW (EGL-614)
FW update from EG failed on timeout (EGL-644)
SMS Message table in manual fixed (EGL-639)
Error of file upload (firmware, cfg) not reported correctly (EGL-680)
Damaged persistent log – partial download only (EGL-681)
Version: 1.3.2
Final version: 1.3.2.3.7 (1.3.2.3.6 confirmed for Kone USA)
Date: 7.4.2022
New features and improvements
Configuration for Thyssen added (EGL-627, 636, 662, 669, 676, 685) – 1.3.2.3.7 only
Automatic MBN profile selection in default configuration allowed (EGL-654)
Bugfixes
VoLTE connection concurrently working with secondary data connection for KRM (EGL-650, 666, 670)
Version: 1.3.1
Final version: 1.3.1.3.1
Date: 13.12.2021
New features and improvements
Change in LTE module to support AT&T after 3G network sunset (22 of February 2022) (EGL-524)
Test call support – for remote testing of calls (EGL-571)
End of call signaling by line current break (CPC – Calling party control) (EGL-580)
Line current increase 40mA, default for USA 30mA, for Australia 40mA (EGL-581)
Bugfixes
FXS line break function – when power error occur during call, no signaling realized when the call ends (EGL-529)
Version: 1.3.0
Final version: 1.3.0.3.3
Date: 6.12.2021
New features and improvements
Lift1 support (EGL-434, 565)
Remote programming of 2N Lift1 by sending an SMS to 2N EasyGate IP
EasyGate IP can signal battery error to 2N Lift1 connected to its FXS port which would then report this error by an operational call
Connection to internet server, HTTP connection, PAP/CHAP support (EGL-17, 403)
Support for connection using local analogue modem
Support for RS232 connection
Configuration web translated to 7 languages (EGL-544, 546)
Adjustable analogue phone line loop current to 15 – 30 mA (default 20 mA) (EGL-525)
Stability improvements – watchdog on connectivity (EGL-106)
Admin as well as admin accepted as login (EGL-412)
Minor configuration web optimalization (EGL-365, 577, 578)
Bugfixes
EasyGate IP appeared offline in Elevator Center when using backup SIM (EGL-583)
Configuration web needs refresh to load properly on slow connection (EGL-493)
Version: 1.2.0
Final version: 1.2.0.2.3
Date: 9.7.2021
New features and improvements
Change in LED functionality details described in manual, allows better recognition of fault states (EGL-382, 509)
Security code visible in section Maintenance/system. Allows connection to Elevator center without paper documentation for the gateway (EGL-375)
Improvement in log functionality, timestamp (EGL-371)
Configuration and monitoring of Gateway by SMS (EGL-431,432, 433, 434, 435)
Security improvements
USB shell secured for system access (EGL-407)
UART shell secured for system access (EGL-406)
Webserver is no more running as root (EGL-410)
Webserver invalidates session after logging out (EGL-411)
Files in file system deleted after deprovisioning and factory reset (EGL-606)
Bugfixes
Improved stability of firmware download (EGL-511, 517)
Configuration web cosmetic improvements (EGL-333, 417, 478)
Configuration web needs refresh to load properly on slow connection (EGL-480)
Version: 1.1.0
Final version: 1.1.0.1.36
Date: 10.2.2021
New features and improvements
NTP used as primary source of time (EGL-419)
Switching between SIM based on network availability (EGL-100)
VoLTE profiles for Australia added (EGL-349)
Adjustable FXS impedance (EGL-319, 356)
Strong password required for login (EGL-347, 366)
Relay output functions implemented (EGL-33)
FXS break function for failure signalization (EGL-339)
CS fallback if SIP not available (EGL-376)
Ringing signal level can be set (EGL-400)
Bugfixes
Corrected instability caused by spaces in SIP parameters (EGL-340)
Measuring of battery internal resistance added for diagnostic purpose (EGL-943)
Decreased data consumption by deleted keep alive packets in EGIP application, only keep alive packed generated by tribble tunnel expected as sufficient (EGL-1058)
Bugfixes
Unexpected short disconnection from network fixed, issue connected with module status reporting (EGL-1378)
Invalid certificate issue, after longer disconnection is the certificate in EGIP invalid and the device can’t connect to Elevator center. Attempts to connect results in high data consumption (EGL-1347]
Version: 1.6.2
Final version: 1.6.2.0.3
Date of issue: 2.10.2025
Only version for EU issued
New features and improvements
Calling party ID (CLI), FSK according to standard ETS300659 implemented (EGL-594)
Possibility to define primary SIM slot (EGL-1211)
Small changes in positions in Web configuration menu (EGL-1212)
Adjustable number of unsuccessful pings to switch to secondary Ping server (EGL-1254)
Reporting of battery capacity for one hour of operation according to EN 81-28 (EGL-1221)
Possibility to switch off internal watchdogs activated by inaccessibility of data or by IMS not ready (no VoLTE available) (EGL-1222)
Security improvements
Configurable system notification before authentication according to IEC62443-4-2 CR 1.12 (EGL-1218)
New SDK with blocking for prohibited localities, downgrade to version without this property not allowed (versions 1.6.0 and lower) (EGL-1299, EGL-1300, EGL-1324)
Configuration interface accessible on WWAN port 8080 – risk when SIM with public IP address is used. Problem in version 1.6.1 only, fixed (EGL-1325)
Bugfixes
Unexpected restart during upgrade connected with low RAM capacity fixed (EGL-1304)
Unexpected sporadic memory leak fixed by memory capacity control (EGL-1256, EGL-1302, EGL-1304)
When PIN on SIM was activated, no IMSI and ICCID information displayed on configuration web in WWAN section – fixed (EGL-1279)
Issue with Busy tone when the outgoing call is refused fixed – connected with new SDK in version 1.6.2.0.2 only (EGL-1315)
Incoming call is refused when connected device picks up the call after first ring – fixed (EGL-1331)
Suppressed generation of not used event connected with temperature change without hysteresis to decrease volume of transmitted data (EGL-1334)
Version: 1.6.0.1.14
Final version: 1.6.0.1.14 – hotfix, not for production
Date of issue: 3.2.2026
New features and improvements
Decreased data consumption by deleted keep alive packets in EGIP application, only keep alive packed generated by tribble tunnel expected as sufficient (EGL-1058)
Bugfixes
Unexpected short disconnection from network fixed, issue connected with module status reporting (EGL-1378)
Invalid certificate issue, after longer disconnection is the certificate in EGIP invalid and the device can’t connect to Elevator center. Attempts to connect results in high data consumption (EGL-1347]
Suppressed generation of not used event connected with temperature change without hysteresis to decrease volume of transmitted data (EGL-1334, EGL-1381)
Version: 1.6.0
Final version: 1.6.0.1.13
Date of issue: 12.3.2025
New features and improvements
Added algorithm for watching IMS state. When the Gateway is connected to 4G network and IMS enabled is set (it means, that VoIP voice connection is demanded), the IMS state “Ready” is expected. When the ready state is lost, restart is performed after 10 minutes. When the IMS ready is not reached after restart, the restart is performed in one hour period till IMS ready state is reached. Restart is inhibited during upgrade and during network selection period including SIM change (EGL-1160)
Lift1 setting support – profile selection, Lift Id number by cloud (EGL-961, EGL-972)
Lift1 security improvement – change of default password by EGIP according to the user demands (EGL-929)
Menu for Lift1 support concentrated to one submenu (EGL-928, EGL-931, EGL-960)
Configuration of Lift1 by message sent from the web interface instead of SMS with the equivalent functionality (EGL-930)
VoLTE support for Vodafone global SIM – both with MCC+MNC 204+04 and 901+28 – proper MBN profile included in FW (EGL-974, EGL-976)
Module EC25-AFFA support – prepared for Verizon, certification necessary (EGL-555)
Change tone progress signaling – till connection to wireless network established, busy tone generated instead of dial tone (EGL-573)
Setting criteria for connection provider change for SIM with roaming to switch to different provider if preferred provider signal has poor quality (EGL-599)
Logging of special Quectel data log to allow remote diagnostic of Quectel/Qualcomm issues (EGL-617)
Setting of Lift1 profiles for profile numbers up to 19 (EGL-647, EGL-773)
Setting of parameter “user agent” (name of VoLTE client) added, default value “EGIP”. Needed for VoLTE connection in some networks (EGL-689)
Manual operator selection for test purposes added (EGL-703)
Software modem support (EGL-623)
Change oi default setting of DTMF in SIP, instead of inband in used RTP event as default setting (EGL-1037)
Default setting for SW modem on devices with SW modem support to Enable (EGL-1111)
IMS state reported to Elevator center by event to improve synchronization of data about IMS (EGL-1109)
Modem UART speed increased from 4800 bps to 9600 bps to improve longer files transmission (EGL-1067)
Change in SMS INF message – added information about FW version, IMEI, IMSI (EGL-1049)
User agent setting change for Australia – not set, value from MBN profile will be used – needed for VoLTE with Telstra (EGL-1082)
Function for MBN profiles actualization forced from internal or external MBN profile database, to be used after FW actualization or factory default setting automatically (EGL-1088)
VoLTE support for Vodafone global SIM in Germany – changes in Vodafone network, appropriate MBN profile added to EGIP. (EGL-789)
MBN database management by EC support in device (not yet in EC) (EGL-914)
Inversion of relay for failure status available, allow to signalize failure when battery empty and device in off state (EGL-769)
Set active CPC for US versions – standard method to signalize end of call in USA (EGL-1017)
Voice menu for Lift1 in all supported languages (EGL-1045)
Security improvements
Replacing of sensitive information from log – keyword for log to wireless network when used is now not visible in log, only information about presence of keyword available (EGL-721)
Denied access to login after three unsuccessful attempts for defined time window according to demand IEC 62443-4-2 CR1.11 (EGL-934)
Reduction of USB access to system services for security reason especially for using EGIP for IP conection (EGL-330, EGL-833, EGL-1020)
Bugfixes
Duplicity of MBN profiles resulted in VoLTE not active, fixed by replacing all profiles in module and loading new set of modules (EGL-1127)
When reinstall of MBN profiles is done with the same profiles as used ones, the following restart was inhibited with the result, that new MBN profile system was not activated – fixed (EGL-1146)
Failure in transmission of events, when communication channel interrupted and restored (EGL-1196)
Delay after FW upgrade in US version, the GW starts functionality after additional restart initiated by watchdog, fixed (EGL-1077, EGL-1085)
User agent setting according the configuration can be replaced by MBN profile to another value – fixed (EGL-1092)
Error in digital signature of MBN profiles in production fixed (EGL-1087, EGL-1078)
Demand of PIN or PUK signaling on web and by LED fixed (EGL-771)
Ping service was stopped after restart of data connection – fixed (EGL-772)
SIM state in menu Network/WWAN monitoring always “Unknown” – fixed (EGL-777)
Error of logging to network with PIN set on some SIM cards – typically in roaming – fixed (EGL-778)
Wrong comment for SMS/Digital input – By opening and by closing has opposite function. In English version only – fixed (EGL-715)
Error in SMS message INF by some combinations of parameters occur – fixed (EGL-718)
Lift 1 setting with wrong parameters refused, but connected Lift 1 still picked up by ring without setting followed – fixed (EGL-775)
Busy tone to FXS was generated when no voice channel available. Result – impossible modem connection in this state - fixed (EGL-814)
Modification of W-dog during process of operator selection to avoid repeated restart when selection takes longer time (EGL-819)
Ping function – server witch IP address was received first from DNS. Now used server in the order according to the list of servers for Ping function (EGL-813)
Factory reset and FW upgrade signaling – red LED only to be active (EGL-831)
Limit for battery voltage dependent on temperature and increasing limit voltage for loading to avoid incorrect error message overvoltage (EGL-812, EGL-941)
When the data connection thru modem during communication is interrupted, for example by disconnecting the analogue modem connected to FXS port, new attempt for data connection can fail – fixed (EGL-975)
Correcting of duplicities in SMS parameters (EGL-1007)
Data connection restored after interruption of physical connection on USB (EGL-1026)
After voice connection forced to 2G/3G because of fallback (VoLTE not supported) EGIP didn’t switch back to 4G although the network is preferred and available (EGL-1048)
Version: 1.5.0
Final version: 1.5.0.0.4
Date: 28.6.2022
New features and improvements
Change in modem to TCP connection allowing to set parameters for connection in bigger detail by parameters (EGL-679, EGL-677)
Change in serial line to TCP connection allowing to set parameters for connection in bigger detail by parameters (EGL-692, EGL-677)
Automatic setting of battery installation time when the device is installed (EGL-686, EGL-691)
Possibility to fix the length od DTMF tones when device connected by VoLTE and DTMF transmitted using RFC2833 (EGL-697)
It is not necessary to use transient version 1.4.0 to use version 1.5.0, it is possible to upgrade from any older version (EGL-698)
Change of factory default settings for key customers and generic version (EGL-702)
Security improvements
Modem and serial line to TCP connection doesn’t allow connection to internal IP address – 127.0.0.1 (localhost) and IP address assigned by mobile operator to the device to avoid unauthorized access (EGL-693)
Bugfixes
Signalization of expired batteries fixed in situation without connection to EC– when battery lifespan overstepped, the device signalized the situation by yellow color of LED Power (EGL-691)
Change of parameters of TCP connection when connection active resulted in internal error of EGIP – fixed (EGL-699)
Version: 1.4.0
Final version: 1.4.0.4.2
Date: 8.4.2022
Not for production
New features and improvements
Set of messages for unsuccessful upgrade enhanced for better diagnostics (EGL-616)
Security improvements
Unused tools and libraries in the filesystem replaced (EGL-409)
Improved protection of configuration files against decryption (EGL-423)
Digital signature of FW as protection against unauthorized FW (EGL-503)
Processes running with necessary privileges only (EGL-605)
Change of encryption algorithm RSA by AES to increase security level (EGL-648)
Bugfixes
VoLTE active even with IMS disabled (EGL-443)
Connecting to EC issue – incorrect time in AT&T network by NTP – solved by NTP off, time from wireless network used (EGL-468]
Web menu Status – visibility of LED submenu fixed (EGL-528)
Calibration constant for voltage measuring fixed in production and repair mechanism for already issued products added to FW (EGL-614)
FW update from EG failed on timeout (EGL-644)
SMS Message table in manual fixed (EGL-639)
Error of file upload (firmware, cfg) not reported correctly (EGL-680)
Damaged persistent log – partial download only (EGL-681)
Version: 1.3.2
Final version: 1.3.2.3.7 (1.3.2.3.6 confirmed for Kone USA)
Date: 7.4.2022
New features and improvements
Configuration for Thyssen added (EGL-627, 636, 662, 669, 676, 685) – 1.3.2.3.7 only
Automatic MBN profile selection in default configuration allowed (EGL-654)
Bugfixes
VoLTE connection concurrently working with secondary data connection for KRM (EGL-650, 666, 670)
Version: 1.3.1
Final version: 1.3.1.3.1
Date: 13.12.2021
New features and improvements
Change in LTE module to support AT&T after 3G network sunset (22 of February 2022) (EGL-524)
Test call support – for remote testing of calls (EGL-571)
End of call signaling by line current break (CPC – Calling party control) (EGL-580)
Line current increase 40mA, default for USA 30mA, for Australia 40mA (EGL-581)
Bugfixes
FXS line break function – when power error occur during call, no signaling realized when the call ends (EGL-529)
Version: 1.3.0
Final version: 1.3.0.3.3
Date: 6.12.2021
New features and improvements
Lift1 support (EGL-434, 565)
Remote programming of 2N Lift1 by sending an SMS to 2N EasyGate IP
EasyGate IP can signal battery error to 2N Lift1 connected to its FXS port which would then report this error by an operational call
Connection to internet server, HTTP connection, PAP/CHAP support (EGL-17, 403)
Support for connection using local analogue modem
Support for RS232 connection
Configuration web translated to 7 languages (EGL-544, 546)
Adjustable analogue phone line loop current to 15 – 30 mA (default 20 mA) (EGL-525)
Stability improvements – watchdog on connectivity (EGL-106)
Admin as well as admin accepted as login (EGL-412)
Minor configuration web optimalization (EGL-365, 577, 578)
Bugfixes
EasyGate IP appeared offline in Elevator Center when using backup SIM (EGL-583)
Configuration web needs refresh to load properly on slow connection (EGL-493)
Version: 1.2.0
Final version: 1.2.0.2.3
Date: 9.7.2021
New features and improvements
Change in LED functionality details described in manual, allows better recognition of fault states (EGL-382, 509)
Security code visible in section Maintenance/system. Allows connection to Elevator center without paper documentation for the gateway (EGL-375)
Improvement in log functionality, timestamp (EGL-371)
Configuration and monitoring of Gateway by SMS (EGL-431,432, 433, 434, 435)
Security improvements
USB shell secured for system access (EGL-407)
UART shell secured for system access (EGL-406)
Webserver is no more running as root (EGL-410)
Webserver invalidates session after logging out (EGL-411)
Files in file system deleted after deprovisioning and factory reset (EGL-606)
Bugfixes
Improved stability of firmware download (EGL-511, 517)
Configuration web cosmetic improvements (EGL-333, 417, 478)
Configuration web needs refresh to load properly on slow connection (EGL-480)
Version: 1.1.0
Final version: 1.1.0.1.36
Date: 10.2.2021
New features and improvements
NTP used as primary source of time (EGL-419)
Switching between SIM based on network availability (EGL-100)
VoLTE profiles for Australia added (EGL-349)
Adjustable FXS impedance (EGL-319, 356)
Strong password required for login (EGL-347, 366)
Relay output functions implemented (EGL-33)
FXS break function for failure signalization (EGL-339)
CS fallback if SIP not available (EGL-376)
Ringing signal level can be set (EGL-400)
Bugfixes
Corrected instability caused by spaces in SIP parameters (EGL-340)