Product Support 2N Lift8

Release notes Lift8 and LiftIP1

Version: 3.1.6

Final version: 3.1.6.0.2

Date: 28.5.2026

New features and improvements

1. Added functionality ‘Push to talk’ when Lift8 Fireman station activated (Lift8-1271)
2. Possibility to select behavior when concurrent alarm call activated on cabin units connected to one central unit, either queuing or connecting to conference according to new parameter 968 (Lift8-1690)
3. Possibility to mute microphone in cabin unit by DTMF signaling ‘9’ to make possible voice connection to the place with very high level of noise. End of muting again by sending DTMF signal ‘9’ Lift8-1699

Security improvements

1. New version of Mbed TLS 4.1.0 applicated (Lift8-1691)
2. New version of LittleFS 2.11.3 applicated (Lift8-1679)
3. Displaying of SMS with sensitive information in log is no more active (Lift8-1711)

Bugfixes

1. Unwanted permanent connection between fireman unit and machine room unit when installed in one shaft (Lift8-1472)
2. Logging time of NTP synchronization uses time after synchronization instead of actual time when synchronization was initiated (Lift8-1656)
3. Maximal length of service password set using service tool is 15 characters, correct value is 16 characters max. (LIFT8-1655)
4. Interrupted connection between 4G data and Ethernet port configured as internal data connection, reconnection of Ethernet cable needed (Lift8-1348)
5. Issue with operational call and checking call with DTMF inband communication (Lift8-1535)
6. SIP call using TCP direct call can’t be executed, P2P solution using TCP is not available – only UTP works correctly for connection without SIP proxy (Lift8-1661, Lift8-1664)
7. Time for checking call is changeable +- 10 minutes although NTP service works correctly (Lift8-1662)
8. Blocked log of central unit followed by restart (Lift8-1665)
9. Incorrect audio test of cabin unit on HW v.4 (Lift8-57)
10. When PIN on SIM in LTE module is changed, needed restart of the module is performed after timeout. Correct behavior is immediate restart (Lift8-685)
11. Repeated use of incorrect PIN for SIM in LTE module can result in SIM blocking. Now only one try of use incorrect PIN performed (Lift8-763)
12. Sporadic error in measured value of battery voltage (Lift8-821)
13. When MBN profile in LTE module is changed, restart of module must be performed (Lift8-1705)
14. Attempt for concurrent connection to central unit by USB and IP result in error of service tool (Lift8-323)
15. Displaying of ICCID in service tool without last digit fixed (Lift8-1261)
16. Communication error on serial line to LTE module resulting in occasional loss of character fixed (Lift8-1677)
17. SMS command for restart L8 RST password doesn’t result in restart of central unit (Lift8-1710)
18. Installation of service tool on new PC was problematic because of incorrect setting of installation process (Lift8-1718)
19. Incorrect message in evacuation mode for Italian language (Lift8-1230)
20. Restart of central unit fails when activated by change parameter 998 from 0 to 1 (Lift8-1714)
21. Operational call doesn’t work until checking call activated at least once (Lift8-1715)

Version: 3.1.5

Final version: 3.1.5.0.2

Date: 25.2.2026

New features and improvements

1. Lift8 – Tamper functionality SMS sending (Lift8-1481)
2. Lift8 – Implementation of INF SMS (LIFT8-1570)
3. Lift8 – Password management changed according to RED/CRA (LIFT8-1590)
4. Lift8 – Change in SMS password, not only numeric, command PWD for keyword change added (LIFT8-1594)
5. Lift8 – Forced change of service password for service tool, SMS and voice menu setting (LIFT8-1597, 1598)
6. Lift8 – Default time after switch on is set to first of February 2026 (LIFT8-1606)
7. Service tool – Added hint describing, that SIP phone number must have prefix ‘sip’ (LIFT8-941)
8. Service tool – Change in password menu place to menu ‘Device’ (LIFT8-1595)
9. Service tool – Change in numbering of parameters, setting of service password from 991 to 891 (LIFT8-1596)
10. Service tool – Added menu for rescue mode configuration - enabling and password (LIFT8-1599)
11. Service tool – Change of maximal length of strings in configuration according to needed values (LIFT8-1605)
12. Service tool – SIP registration time limits set to 60 – 3600s to avoid setting of too short values resulting in wrong functionality, setting 0 results in 300s (default value) (LIFT8-1616, 555)
13. Service tool – format validation of phone numbers for notification events (LIFT8-1622)

Security improvements

1. Lift8 – scan product for known open source vulnerabilities and address issues according to the Axis Vulnerability Management Policy (LIFT8-1444)
2. Lift8 – SBOM delivered for every release (LIFT8-1444)
3. Lift8 – Secure communication with device during configuration (LIFT8-1467)
4. Lift8 – Change in setting of passwords, demanded change of admin password and service password prior any changes (LIFT8-1515)
5. Lift8 – After setting wrong password 3 times, the device is blocked for password input for defined time (LIFT8-1581)

Bugfixes

1. Lift8 - RS232 module – AT command issue resulting in device restart (LIFT8-1485)
2. Lift8 - Error in planned checking call (LIFT8-1573)
3. Lift8 - SIP call over TCP protocol can’t be realized (LIFT8-1608)
4. Lift8 – Date can’t be set using phone call (LIFT8-179)
5. Lift8 – Issue with combination of wireless data connection and LAN connection (LIFT8-616)
6. Lift8 – Direct call to IP address doesn’t work when TCP protocol used (LIFT8-1563)
7. Lift8 – issues with quality of reproduced sound in announcements (LIFT8-1301)
8. Lift8 – When password for rescue mode end demanded, control of password parameter provided (LIFT8-1493)
9. Lift8 – Combination of FW upgrade in progress and sending event SMS results in unsuccessful upgrade (LIFT8-1549)
10. Lift8 - Invalid length of service password sent by SMS results in device reset (LIFT8-1610)
11. Lift8 – Setting of date to invalid value can result in need to perform firmware upgrade (LIFT8-179)
12. Lift8 – Sending SMS event without response results in LTE module reset (LIFT8-1620)
13. Service tool – Event configuration issue when configuration loaded from device, it can’t be loaded back (LIft8-1614)
14. Service tool – For some new functionalities missing translation to other languages than English, fixed (LIFT8-1430, 1572)
15. Service tool – issue with blocking tool when invalid date set, added checking of tine in device after setting (LIFT8-1532)
16. Service tool – When device connected by TCP, change in language od service tool results in device restart (LIFT8-1623)

Version: 3.1.4

Final version: 3.1.4.0.1

Date: 26.11.2025

New features and improvements

1. Lift8 – TCP signaling for SIP connection added – both TCP and UDP available (LIFT8-1041)
2. Lift8 – camera functionality is not supported for FW versions 3.x both for new and old version of hardware (LIFT8-1560)
3. Lift8 – User Agent field filled with actual device or application (LIFT8-1043)
4. Communicator – signaling of data communication error added (LIFT8-1495)
5. Lift8 server – repeated question whether configuration files should be deleted to avoid unwanted deleting of application data (LIFT8-1476)

Security improvements

1. Lift8 – conformity with standard EMN 18031 approved (LIFT8-1091)
2. Lift8 – conformity with standard EN 303 645 approved (LIFT8-1139)

Bugfixes

1. Lift8 – unreliable upgrade of LTE module fixed (LIFT8-1415)
2. Lift8 – identification of used audio unit by SIP call in evacuation mode (LIFT8-1420, LIFT8-1426)
3. Lift8 – repeated attempt to SIP registration although the data connection is not available (LIFT8-753)
4. Lift8 – incorrect functionality of machine room unit when invert of Alarm input applicated (LIFT8-1247)
5. Lift8 – audio unit Compact can be used in cabin only – changed to any position (LIFT8-1502)
6. Lift8 – audio quality in call improved, disturbance in call and in reproduced sounds fixed (LIFT8-1418, LIFT8-1301)
7. Lift8 LTE – added MBN profile for Vodafone (LIFT8-1519)
8. Service tool – user message can’t be deleted during playback, delete function blocked. Improved loading user message (LIFT8-1380, LIFT8-1386)

Version: 3.0.0 – Hardware version 4 support

Final version: 3.0.0.0.8

Date: 15.10.2025

New features and improvements

1. Lift8 – Reporting of battery capacity for one hour of operation according to EN 81-28 (LIFT8-1275)
2. Lift8 – forced test alarm set by default to 30s to fulfill demand of EN 81-28 by default (LIFT8-1407)
3. Lift8 – Ethernet port placed on base board of L8 HW version 4, no additional Ethernet board needed (LIFT8-950)
4. Lift8 – USB C port supported on base board of L8 HW version 4, instead of previous USB B (LIFT8-988)
5. Lift8 – Change in battery and power source voltage displaying – two separated values (LIFT8-456)
6. Lift8 – Improved signalization of data connection status by LED (LIFT8-13290)
7. Lift8 – TCP signaling option added (LIFT8-1041, LIFT8-1042)
8. Lift8, Communicator – Unification of user agent reporting with other 2N products (LIFT8-1043, LIFT8-1044)
9. Lift8, Communicator – Possibility to confirm checking call by connecting the call without any additional confirmation (LIFT8-1257)
10. Lift8 LTE – Possibility to select MBN profile for LTE module, needed for VoLTE support for some operators, profiles added to upgrade packets (LIFT8-1282, LIFT-1284, LIFT8-1285)
11. Control panel – Reporting extended by possibility to report time and date of last successful call (LIFT8-1258)
12. Control panel – When the interval for checking call is set to 72 hour (default value – 3 days), the interval 74 hour is accepted, error is reported after this time (LIFT8-904, LIFT8-1385)
13. Control panel – separated upgrade for LTE module and FW in Lift8 to prevent problems when upgrade is done in one step over wireless connection (LIFT8-1401)
14. Communicator – Change of map used for localization of installation, instead of BingMaps used OpenStreetMaps because of licensing issue (LIFT8-1288)
15. Communicator – Improved reporting checking call by adding information about results (LIFT8-1391)

Security improvements

1. Lift8 - Trust zone supported for HW version 4, secure memory area to save information, which should be kept private (LIFT8-960)
2. Lift8 – Secure boot supported for HW version 4, verified FW loading protected against use of unauthorized firmware (LIFT8-1019, LIFT8-1116)
3. Lift8 – Verification of authenticity and integrity of firmware for update (LIFT8-1156, LIFT8-1157)
4. Lift8 - Cryptography protection of personal data transiting between device and associated services (LIFT8-1187)
5. Lift8 - Libraries of third party upgraded to latest versions (LittleFS, LWIP, TLS…) (LIFT8-1208, LIFT8-1262, LIFT8-1264, LIFT8-1313)
6. Lift8 – Tamper added for HW version 4, possibility to report opening of the case (LIFT8-999, LIFT8-989, LIFT8-1029)
7. Lift8 – Mechanism against unauthorized authentication by repeated access looking for and and keyword by blocking interface (LIFT8-1144)
8. Lift8 – Protection against unauthorized debug processing (LIFT8-1179)
9. Lift8 – Protecting user data by replacing after factory reset (LIFT8-1194, LIFT8-1195, LIFT8-1196)
10. Lift8 LTE - New SDK for LTE module used – RED compliant (Lift8-1346)

Bugfixes

1. Lift8 – Lost IP connection when static IP address set – fixed (LIFT8-1090)
2. Lift8 – Incorrect LED signalization when connection in roaming active (LIFT8-816, LIFT8-1078)
3. Lift8 – Restart activated by SIP service by call is delayed for 2-3 minutes – fixed (LIFT8-1287, LIFT8-1292, LIFT8-1408)
4. Lift8 – Error in invite by SIP call, missing TAG fixed (LIFT8-1278, LIFT8-1399)
5. Lift8 – Default value for forced call changed to 30s to allow initialization of forced call according EN 81-28 in default setting (LIFT8-1388)
6. Lift8 LTE – Unreliable FW upgrade when LTE module inserted – fixed (LIFT8-801)
7. Lift8 LTE – Upgrade of module failed because of memory shortage – fixed (LIFT8-1333)

Version: 2.9.2 – Bugfix version

Final version: 2.9.2.0.5

Date: 17.3.2025

New features and improvements

1. Lift8 – Functionality of machine room communicator according EN 81-72, activation of microphone by button demanded (LIFT8-1014)
2. Lift8 LTE – possibility to set preferred DNS 1 and 2 added (LIFT8-1079)

Bugfixes

1. Lift8 – reporting identification od calling location in higher detail (LIFT8-449)
2. Lift8 LTE – long time period for SIM logging for some operators – fixed by longer timeout for critical operations (LIFT8-1081)
3. Control panel – Notification of license expiration of Lift8 server added, correct message when license expired displayed, login with expired license allowed with limited functionality (LIFT8-576, LIFT8-847, LIFT8-849, LIFT8-568, LIFT8-1232)
4. Communicator – limits for setting of port numbers replaced (LIFT8-523)
5. Lift8 server – Expiration of license correctly reported (LIFT8-868, LIFT8-1034)

Version: 2.9.0 – Evacuation scenario support, control center capacity increase

Final version: 2.9.0.0.2

Date: 6.12.2024

New features and improvements

1. Lift8 – evacuation mode available, up to 64 communication units, driven from connected IP phone – see manual for details (LIFT8-931, LIFT8-932, LIFT8-933, LIFT8-934, LIFT8-946, LIFT8-949, LIFT8-953, LIFT8-1036)
2. Lift8 – support of two Fireman units in one shaft available (LIFT8-1013)
3. Lift8 LTE – possibility to set PAP, CHAP authorization for wireless connection added (LIFT8-1052)
4. Control panel – counter of control and alarm call added (Lift8-776, Lift8-1038)
5. Lift8 server, communicator, control panel – improvements to increase number of connected devices up to 5000 units with keeping acceptable response for demanded operations (Lift8-350, Lift8-839, Lift8-865, Lift8-908)
6. Lift8 Control panel, Communicator – listing of information organized by groups in alphabetic order instead of time of recording – better orientation in listings (LIFT8-524)

Bugfixes

1. Control panel – increased number of control calls and reports to be registered to support traffic for higher number of connected devices (Lift8-882, Lift8-883).
2. Communicator – global map functionality switched off because of issues with map source and wrong function of displaying for 100+ points in map. Plam to solve this issue in future (LIFT8-843, LIFT8-1032).
3. Communicator – acceptation of identification number for incoming call with prefix * to be able to accept signaling from some SIP connection providers (LIFT8-708).
4. Communicator, Lift8 server – high number of registered control calls and alarm calls (about 50 000+) resulted into Lift8 server crash when higher amount of incoming calls occur concurrently (Lift8-883)

Version: 2.8.7 – 100 Mb LAN connection

Final version: 2.8.7.33.33

Date: 24.4.2024

New features and improvements

1. Lift8 – support for LAN communication board 100 Mb added (LIFT8-595, LIFT8-631)
2. Lift8 – second DNS server setting available (LIFT8-647, LIFT8-665)
3. Service tool - configurable space between DTMF tones during configuration to allow setting when issues with DTMF transmitting occur (LIFT8-677)
4. Service tool – changed provider of map source (LIFT8-734, LIFT8-701)
5. LiftIP1 – Incoming call by default configuration, ability to switch to voice menu by DTMF 9 (LIFT8-155)

Bugfixes

1. Lift8 – incorrect message about end of button stuck error when alarm activated – fixed (LIFT8-640, LIFT8-327)
2. Lift8 – error of wireless module registration fixed (LIFT8-745)
3. Lift8 LTE – MBN profile activation check after restart – improved reliability of VoLTE calls (LIFT8-676)
4. Lift8 LTE – upgrade of central unit blocked when SIM with PIN inserted and incorrect PIN set in Lift8 (LIFT8-667)
5. Lift8 LTE – change of SIP availability according to 2G/4G technology changes (LIFT8-675, LIFT8-753)
6. LIFT8 LTE – when LTE module inserted, upgrade from older versions which doesn’t support LTE module is not possible - fixed (LIFT8-683)
7. LIFT8 LTE – module restart after VoLTE activation on SIM – necessary for VoLTE activation (LIFT8-754)
8. Service tool – configuration blocked during loading to prevent data damage (LIFT8-662)
9. Service tool – visualization of line speed for LAN corrected after connecting device, no restart of lift8 needed (LIFT8-723)
10. Service tool – unsuccessful FW upgrade with LTE module thru USB (LIFT8-791)
11. Service tool – compatibility of different versions of service tool and L8-server allowed (LIFT8-569)
12. L8-Server – incorrect setting if SIP domain – used parameter from SIP server (LIFT8-795, LIF8-798)
13. L8-Server – incorrect length of CLIP (less then minimal length 5 digits) results in server restart – fixed (LIFT8-680)

     

     

    Version: 2.8.5 – LTE support

    Final version: 2.8.5.33.28

    Date: 27.11.2023

    New features and improvements

14. Lift8 - France language added to voice menu (LIFT8-527)
15. Lift8 – Support for LTE module integration and communication (LIFT8-110), (LIFT8-111), (LIFT8-112), (LIFT8-116), (LIFT8-121), (LIFT8-130), (LIFT8-137), (LIFT8-138), (LIFT8-140), (LIFT8-374)
16. Lift8 – SIP call using LTE module and wireless data connection implemented, direction of call defined by prefix (LIFT8-123), (LIFT8-124), (LIFT8-125), (LIFT8-114), (LIFT8-128), (LIFT8-134), (LIFT8-553), (LIFT8-634)
17. Lift8 – VoLTE call support using LTE module (LIFT8-117)
18. Lift8 – SMS services added to support LTE module (LIFT8-444)
19. Lift8 – Data connection support for LTE module (LIFT8-122)
20. Lift8 – Firmware in LTE module upgrade support (LIFT8-136)
21. Lift8 – LED functionality changed to support new features connected with LTE module use, description of new functionality in user manual (LIFT8-591)
22. Lift8 – Compressing of log files configured, block compressed when size 10MB reached (LIFT8-528)
23. Lift8 – Reporting of LTE module FW version, both the application FW and module FW, adding to log (LIFT8-582), (LIFT8-587)
24. Lift8 – Restart of LTE module when the malfunction detected, including logging of this situation with details allowing troubleshooting (LIFT8-108)
25. Service tool – SIP and VoLTE status visualization when LTE module assembled (LIFT8-435), (LIFT8-543)
26. Service tool – Reset for I/O module added to set default settings (LIFT8-359)
27. L8-Server – Repeating unsuccessful registration attempt till restart of application fixed (LIFT8-337)

Bugfixes

1. Lift8 - Change in checking call DTMF timing, unwanted space fixed (LIFT8-445)
2. Lift8 – Incorrect DTMF signaling during alarm call fixed, timing of signals for call end changed (LIFT8-446)
3. Lift8 – Watchdog for SIP connection on Ethernet port added, restart of SIP engine when registration failed (LIFT8-424), (LIFT8-309)
4. Lift8 – Day of week for checking call functionality fixed (LIFT8-251)
5. Lift8 – Default time setting from programming tool by DTMF fixed (LIFT8-333)
6. Lift8 – Parameter ‘day of week’ (986) shifted, beginning of week now Monay (LIFT8-325)
7. Lift8 – Incorrect finishing of SIP checking call thru Ethernet connection (LIFT8-615)
8. Lift8 – Default battery expiration time changed from 3 years to 2 years, according standards (LIFT8-632)
9. Lift8 – When PIN for SIM is filled with incorrect value, the PIN is after restart repeated till SIM blocked and PUK needed, now blocking of SIM avoided and wrong PIN indicated by LED (LIFT8-635)
10. Service tool – Beep notification of I/O module, input and output divided (LIFT8-330)
11. Service tool – Popup notification of I/O module status can result in application crash, fixed (LIFT8-425)
12. Service tool – Filtering of connection status fixed (LIFT8-464)
13. Service tool – Connection attempt during device factory reset results in impossibility of later connection, fixed (LIFT8-439)
14. Communicator – error in compatibility of database resulting to impossibility to save time setting fixed (LIFT8-511)
15. Communicator – change in PJSIP licensing done because of different mode of use (LIFT8-418)
16. Communicator - License politics error fixed, real status of license displayed (LIFT8-522)
17. Control panel – Incorrect export of Operational Calls report – format error fixed (LIFT8-410), (LIFT8-411)
18. Control panel – Export of alarm call identification file corrected (LIFT8-430)
19. Control panel – Incorrect way for new group creation by superuser in another group fixed (LIFT8-381)
20. Control panel – License politics error fixed, group licenses working after expiration (LIFT8-520), (LIFT8-517), (LIFT8-518)
21. Control panel – Communication with Lift8 during the call may result in application crash, fixed (LIFT8-611)
22. Graphic of tools – Resolution of application window setting changed (LIFT8-513)
23. All tools – After replacing from computer some empty directories resists, fixed (LIFT8-536)
24. Whole system – 2N logo changed (LIFT8-419)

Version: 2.8.4 - Schmitt

Final version: 2.8.4.33.21

Date: 15.5.2023

New features and improvements

1. Change in licensing – control of connected devices, whether the amount agrees with license, timing of trial time period improved (LIFT8-438), (LIFT-486)
2. E-mail notification of exceeding number of licenses added (LIFT8-488)

Bugfixes

1. Fixed errors in German translation for service tool (LIFT8-458)

Version: 2.8.4

Final version: 2.8.4.33.18

Date: 19.12.2022

New features and improvements

1. Web address changed from www.2n.cz to www.2n.com (LIFT8-377)
2. Lift8 - Voice menu for Spain added (LIFT8-365)
3. Lift8 - Voice menu for Latin America (Spain) added (LIFT8-366)
4. Service tool – Fixed position of parameter groups, independently on languages (LIFT8-375)
5. L8 server - Support of LiftIP2 on Lift8 server (LIFT8-326)
6. Communicator - Dual audio output added – different audio output can be set for ringing and for call, improved management of connected audio devices (LIFT8-396)
7. Control Panel – Increased maximal length of intercom name from 15 to 49 characters
8. Control Panel – Specific response (Custom) to Lift8 to confirm Checking call, Alarm call and Call to Lift8 added (LIFT8-393, LIFT8-394)

Bugfixes

1. Fixed translation in tool texts and hints (LIFT8-373, LIFT8-200, LIFT8-372)
2. Fixed issues in manuals and in references to manual in tools (LIFT8-334, LIFT8-335)
3. Lift8, LiftIP – Support of SIP proxy registration after change in Netstar (LIFT8-391, LIFT8-405)
4. Service tool - Wrong functionality of calendar, when month changed, day of weeks stays from last month (LIFT8-328)
5. LiftIP – Checking call timeout can result to incorrect end of call when registration during the waiting changes (LIFT8-403)
6. LiftIP – Finding in logs improved, wrong function of help fixed (LIFT8-245)
7. Service tool - Selection of connection in service tool for LiftIP selects more than one connection (LIFT8-361)
8. Service tool – Hidden keyword for parameter 1122 – keyword for RTSP connection to camera in service tool (LIFT8-305)
9. Service tool – Improved search in logs, now is case sensitive (LIFT8-371)
10. Service tool – Graphical view to configuration fixed (LIFT8-380)
11. L8 Server – MapQuest API service change supported to keep map functionality unchanged (LIFT8-388)
12. L8 Server – Setting detail of server fixed (LIFT8-515)
13. Communicator - During incoming call to Communicator, the map is not visible (LIFT8-347)
14. Communicator – Wrong position of intercom position on map, when windows size changed, improved accuracy of position (LIFT8-316, LIFT8-329, LIFT8-360)
15. Communicator – Incorrect setting of audio device for input and output (LIFT8-397)
16. Communicator – Incorrect displaying of names of audio devices – 32 characters only (LIFT8-398)
17. Communicator – Adding new Lift8 fails in specific circumstances (LIFT8-401)
18. Control Panel - List of intercoms in Control panel doesn’t show added intercom before refresh, not full view to all intercoms as admin without selected group of intercom (LIFT8-356)
19. Control Panel - Configuration of maps available to prevent issues connected with end of service MapQuest (LIFT8-363)
20. Control Panel - Fixed error in setting of test E-mail (LIFT8-302)
21. Control Panel – CPC Antenna 2N Extension support bug fixed (LIFT8-315)
22. Control Panel – Specific response to Lift8 to confirm Checking call, Alarm call and Call to Lift8 fixed (LIFT8-393, LIFT8-394)
23. Control Panel – ID extraction from CPC Antenna 2N ext. protocol fixed (LIFT8-357)
24. Control Panel – Export of alarm call has missing information about Agent, when the value is Server (LIFT8-343)
25. Control Panel – Export of call from intercom detail shows only test call (LIFT8-407)

Version: 2.8.3

Final version: 2.8.3.33.14

Date: 28.6.2022

New features and improvements

1. Lift8 – Identification of lift shaft in alarm call by voice message. (Lift8-25)
2. Lift8 – Alarm button self-test added, special type of alarm button needed. (Lift8-27, LIFT8-209)
3. Lift8 – Italian voice menu added. (LIFT8-31)
4. Lift8 – Polish voice menu added. (LIFT8-185)
5. Lift8 - Possibility to set siren output on the machine room communicator when alarm call activated. (LIFT8-33)
6. Lift8 - Information E-mail from alarm call to Control Panel (additional functionality to E-mail notification about checking call). (LIFT8-12)
7. LiftIP – Italian voice menu added. (LIFT8-32)
8. All tools - GUI of Lift8 supports seven languages: CZE, ENG, ESP, GER, FRA, ITA, RU. (LIFT8-6)
9. Communicator - Plan or map of the area with marked locality of lift is visible during emergency call. (LIFT8-7)
10. Communicator - Possibility to set keyboard shortcuts for define actions in Communicator to allow use of keyboard emulator. (LIFT8-20)
11. Communicator – Test of microphone connection added. (Lift8-189)

Bugfixes

1. Installation - Missing DLL libraries when Lift8 tools installed, mostly connected with Win10. (LIFT8-59, LIFT8-89)
2. Lift8 - Time overflow error – when Lift8 runs 49,7 days, timer overflow can result into unexpected irregularities in function. (LIFT8-36)
3. Lift8 – Alarm call with CPC Antena support failed in intercom identification – first number lost. (LIFT8-197)
4. Lift8 - Time synchronization by SNTP on by default – log with correct timing supported. (LIFT8-56)
5. LiftIP – issue with Payload Type for DTMF. (LIFT8-159, LIFT8-19)
6. LiftIP – communication issue with AVAYA – too long packets. (LIFT8-42)
7. LiftIP – After change of configuration confirmed by password, wrong password reported. (LIFT8-254)
8. Service tool - doesn’t correctly display all parameters depending on screen resolution. (LIFT8-52, LIFT8-147)
9. Service tool – incorrect filter, only numbers applied. (LIFT8-257)
10. Service tool – Device info error when older device connected because of missing hwinfo. (LIFT8-249)
11. L8 Server - Special characters for example - !@#$% - can’t be used as part of the SIP password. (LIFT8-10)
12. L8 Server -after change of IP address on connected PC registration failure occur. (LIFT8-90)
13. L8 Server – Error occur when E-mail report sent to three or more address. (Lift8-344)
14. L8 Server – Empty E-mail address for notification results into application lock or sending error. (LIFT8-247, LIFT8-301)
15. Communicator - Deleting of Control panel user, who is registered in Communicator results In lock of the application. (LIFT8-24)
16. Communicator - crash when display resolution changes. (Lift8-146)
17. Communicator - direct call user is not correctly signed off after user delete performed. (LIFT8-148)
18. Communicator - doesn’t allow moving of map by scrollbar. (LIFT8-171)
19. Communicator – when size of map changed, the change is not permanent. (LIFT8-252)
20. Communicator - crash when display resolution changes. (Lift8-146)
21. Communicator - direct call user is not correctly signed off after user delete performed.
22. Communicator - doesn’t allow moving of map by scrollbar. (LIFT8-171)
23. Communicator – when size of map changed, the change is not permanent. (LIFT8-252)
24. Communicator - doesn’t allow moving of map by scrollbar. (LIFT8-171)
25. Communicator – when size of map changed, the change is not permanent. (LIFT8-252)
26. Communicator - doesn’t allow moving of map by scrollbar. (LIFT8-171)
27. Communicator – when size of map changed, the change is not permanent. (LIFT8-252)
28. Communicator – When filtering by length of call or agent used, application crashes. (LIFT8-313)
29. Control panel - When Call server is set, correct visualization of all details in graphics is not guaranteed. (LIFT8-47)
30. Control panel – forced save of storage setting before next step can be performed. (LIFT8-158)
31. Control panel – When more intercoms on one plan placed, it is not possible to remove any of them. (LIFT8-217)
32. Control Panel – Test of storge availability, if lost, warning generated. (LIFT8-223)
33. Control Panel – searching of intercom by address in map failed. (LIFT8-92)

Release notes Lift8 and LiftIP1

Version: 3.1.6

Final version: 3.1.6.0.2

Date: 28.5.2026

New features and improvements

1. Added functionality ‘Push to talk’ when Lift8 Fireman station activated (Lift8-1271)
2. Possibility to select behavior when concurrent alarm call activated on cabin units connected to one central unit, either queuing or connecting to conference according to new parameter 968 (Lift8-1690)
3. Possibility to mute microphone in cabin unit by DTMF signaling ‘9’ to make possible voice connection to the place with very high level of noise. End of muting again by sending DTMF signal ‘9’ Lift8-1699

Security improvements

1. New version of Mbed TLS 4.1.0 applicated (Lift8-1691)
2. New version of LittleFS 2.11.3 applicated (Lift8-1679)
3. Displaying of SMS with sensitive information in log is no more active (Lift8-1711)

Bugfixes

1. Unwanted permanent connection between fireman unit and machine room unit when installed in one shaft (Lift8-1472)
2. Logging time of NTP synchronization uses time after synchronization instead of actual time when synchronization was initiated (Lift8-1656)
3. Maximal length of service password set using service tool is 15 characters, correct value is 16 characters max. (LIFT8-1655)
4. Interrupted connection between 4G data and Ethernet port configured as internal data connection, reconnection of Ethernet cable needed (Lift8-1348)
5. Issue with operational call and checking call with DTMF inband communication (Lift8-1535)
6. SIP call using TCP direct call can’t be executed, P2P solution using TCP is not available – only UTP works correctly for connection without SIP proxy (Lift8-1661, Lift8-1664)
7. Time for checking call is changeable +- 10 minutes although NTP service works correctly (Lift8-1662)
8. Blocked log of central unit followed by restart (Lift8-1665)
9. Incorrect audio test of cabin unit on HW v.4 (Lift8-57)
10. When PIN on SIM in LTE module is changed, needed restart of the module is performed after timeout. Correct behavior is immediate restart (Lift8-685)
11. Repeated use of incorrect PIN for SIM in LTE module can result in SIM blocking. Now only one try of use incorrect PIN performed (Lift8-763)
12. Sporadic error in measured value of battery voltage (Lift8-821)
13. When MBN profile in LTE module is changed, restart of module must be performed (Lift8-1705)
14. Attempt for concurrent connection to central unit by USB and IP result in error of service tool (Lift8-323)
15. Displaying of ICCID in service tool without last digit fixed (Lift8-1261)
16. Communication error on serial line to LTE module resulting in occasional loss of character fixed (Lift8-1677)
17. SMS command for restart L8 RST password doesn’t result in restart of central unit (Lift8-1710)
18. Installation of service tool on new PC was problematic because of incorrect setting of installation process (Lift8-1718)
19. Incorrect message in evacuation mode for Italian language (Lift8-1230)
20. Restart of central unit fails when activated by change parameter 998 from 0 to 1 (Lift8-1714)
21. Operational call doesn’t work until checking call activated at least once (Lift8-1715)

Version: 3.1.5

Final version: 3.1.5.0.2

Date: 25.2.2026

New features and improvements

1. Lift8 – Tamper functionality SMS sending (Lift8-1481)
2. Lift8 – Implementation of INF SMS (LIFT8-1570)
3. Lift8 – Password management changed according to RED/CRA (LIFT8-1590)
4. Lift8 – Change in SMS password, not only numeric, command PWD for keyword change added (LIFT8-1594)
5. Lift8 – Forced change of service password for service tool, SMS and voice menu setting (LIFT8-1597, 1598)
6. Lift8 – Default time after switch on is set to first of February 2026 (LIFT8-1606)
7. Service tool – Added hint describing, that SIP phone number must have prefix ‘sip’ (LIFT8-941)
8. Service tool – Change in password menu place to menu ‘Device’ (LIFT8-1595)
9. Service tool – Change in numbering of parameters, setting of service password from 991 to 891 (LIFT8-1596)
10. Service tool – Added menu for rescue mode configuration - enabling and password (LIFT8-1599)
11. Service tool – Change of maximal length of strings in configuration according to needed values (LIFT8-1605)
12. Service tool – SIP registration time limits set to 60 – 3600s to avoid setting of too short values resulting in wrong functionality, setting 0 results in 300s (default value) (LIFT8-1616, 555)
13. Service tool – format validation of phone numbers for notification events (LIFT8-1622)

Security improvements

1. Lift8 – scan product for known open source vulnerabilities and address issues according to the Axis Vulnerability Management Policy (LIFT8-1444)
2. Lift8 – SBOM delivered for every release (LIFT8-1444)
3. Lift8 – Secure communication with device during configuration (LIFT8-1467)
4. Lift8 – Change in setting of passwords, demanded change of admin password and service password prior any changes (LIFT8-1515)
5. Lift8 – After setting wrong password 3 times, the device is blocked for password input for defined time (LIFT8-1581)

Bugfixes

1. Lift8 - RS232 module – AT command issue resulting in device restart (LIFT8-1485)
2. Lift8 - Error in planned checking call (LIFT8-1573)
3. Lift8 - SIP call over TCP protocol can’t be realized (LIFT8-1608)
4. Lift8 – Date can’t be set using phone call (LIFT8-179)
5. Lift8 – Issue with combination of wireless data connection and LAN connection (LIFT8-616)
6. Lift8 – Direct call to IP address doesn’t work when TCP protocol used (LIFT8-1563)
7. Lift8 – issues with quality of reproduced sound in announcements (LIFT8-1301)
8. Lift8 – When password for rescue mode end demanded, control of password parameter provided (LIFT8-1493)
9. Lift8 – Combination of FW upgrade in progress and sending event SMS results in unsuccessful upgrade (LIFT8-1549)
10. Lift8 - Invalid length of service password sent by SMS results in device reset (LIFT8-1610)
11. Lift8 – Setting of date to invalid value can result in need to perform firmware upgrade (LIFT8-179)
12. Lift8 – Sending SMS event without response results in LTE module reset (LIFT8-1620)
13. Service tool – Event configuration issue when configuration loaded from device, it can’t be loaded back (LIft8-1614)
14. Service tool – For some new functionalities missing translation to other languages than English, fixed (LIFT8-1430, 1572)
15. Service tool – issue with blocking tool when invalid date set, added checking of tine in device after setting (LIFT8-1532)
16. Service tool – When device connected by TCP, change in language od service tool results in device restart (LIFT8-1623)

Version: 3.1.4

Final version: 3.1.4.0.1

Date: 26.11.2025

New features and improvements

1. Lift8 – TCP signaling for SIP connection added – both TCP and UDP available (LIFT8-1041)
2. Lift8 – camera functionality is not supported for FW versions 3.x both for new and old version of hardware (LIFT8-1560)
3. Lift8 – User Agent field filled with actual device or application (LIFT8-1043)
4. Communicator – signaling of data communication error added (LIFT8-1495)
5. Lift8 server – repeated question whether configuration files should be deleted to avoid unwanted deleting of application data (LIFT8-1476)

Security improvements

1. Lift8 – conformity with standard EMN 18031 approved (LIFT8-1091)
2. Lift8 – conformity with standard EN 303 645 approved (LIFT8-1139)

Bugfixes

1. Lift8 – unreliable upgrade of LTE module fixed (LIFT8-1415)
2. Lift8 – identification of used audio unit by SIP call in evacuation mode (LIFT8-1420, LIFT8-1426)
3. Lift8 – repeated attempt to SIP registration although the data connection is not available (LIFT8-753)
4. Lift8 – incorrect functionality of machine room unit when invert of Alarm input applicated (LIFT8-1247)
5. Lift8 – audio unit Compact can be used in cabin only – changed to any position (LIFT8-1502)
6. Lift8 – audio quality in call improved, disturbance in call and in reproduced sounds fixed (LIFT8-1418, LIFT8-1301)
7. Lift8 LTE – added MBN profile for Vodafone (LIFT8-1519)
8. Service tool – user message can’t be deleted during playback, delete function blocked. Improved loading user message (LIFT8-1380, LIFT8-1386)

Version: 3.0.0 – Hardware version 4 support

Final version: 3.0.0.0.8

Date: 15.10.2025

New features and improvements

1. Lift8 – Reporting of battery capacity for one hour of operation according to EN 81-28 (LIFT8-1275)
2. Lift8 – forced test alarm set by default to 30s to fulfill demand of EN 81-28 by default (LIFT8-1407)
3. Lift8 – Ethernet port placed on base board of L8 HW version 4, no additional Ethernet board needed (LIFT8-950)
4. Lift8 – USB C port supported on base board of L8 HW version 4, instead of previous USB B (LIFT8-988)
5. Lift8 – Change in battery and power source voltage displaying – two separated values (LIFT8-456)
6. Lift8 – Improved signalization of data connection status by LED (LIFT8-13290)
7. Lift8 – TCP signaling option added (LIFT8-1041, LIFT8-1042)
8. Lift8, Communicator – Unification of user agent reporting with other 2N products (LIFT8-1043, LIFT8-1044)
9. Lift8, Communicator – Possibility to confirm checking call by connecting the call without any additional confirmation (LIFT8-1257)
10. Lift8 LTE – Possibility to select MBN profile for LTE module, needed for VoLTE support for some operators, profiles added to upgrade packets (LIFT8-1282, LIFT-1284, LIFT8-1285)
11. Control panel – Reporting extended by possibility to report time and date of last successful call (LIFT8-1258)
12. Control panel – When the interval for checking call is set to 72 hour (default value – 3 days), the interval 74 hour is accepted, error is reported after this time (LIFT8-904, LIFT8-1385)
13. Control panel – separated upgrade for LTE module and FW in Lift8 to prevent problems when upgrade is done in one step over wireless connection (LIFT8-1401)
14. Communicator – Change of map used for localization of installation, instead of BingMaps used OpenStreetMaps because of licensing issue (LIFT8-1288)
15. Communicator – Improved reporting checking call by adding information about results (LIFT8-1391)

Security improvements

1. Lift8 - Trust zone supported for HW version 4, secure memory area to save information, which should be kept private (LIFT8-960)
2. Lift8 – Secure boot supported for HW version 4, verified FW loading protected against use of unauthorized firmware (LIFT8-1019, LIFT8-1116)
3. Lift8 – Verification of authenticity and integrity of firmware for update (LIFT8-1156, LIFT8-1157)
4. Lift8 - Cryptography protection of personal data transiting between device and associated services (LIFT8-1187)
5. Lift8 - Libraries of third party upgraded to latest versions (LittleFS, LWIP, TLS…) (LIFT8-1208, LIFT8-1262, LIFT8-1264, LIFT8-1313)
6. Lift8 – Tamper added for HW version 4, possibility to report opening of the case (LIFT8-999, LIFT8-989, LIFT8-1029)
7. Lift8 – Mechanism against unauthorized authentication by repeated access looking for and and keyword by blocking interface (LIFT8-1144)
8. Lift8 – Protection against unauthorized debug processing (LIFT8-1179)
9. Lift8 – Protecting user data by replacing after factory reset (LIFT8-1194, LIFT8-1195, LIFT8-1196)
10. Lift8 LTE - New SDK for LTE module used – RED compliant (Lift8-1346)

Bugfixes

1. Lift8 – Lost IP connection when static IP address set – fixed (LIFT8-1090)
2. Lift8 – Incorrect LED signalization when connection in roaming active (LIFT8-816, LIFT8-1078)
3. Lift8 – Restart activated by SIP service by call is delayed for 2-3 minutes – fixed (LIFT8-1287, LIFT8-1292, LIFT8-1408)
4. Lift8 – Error in invite by SIP call, missing TAG fixed (LIFT8-1278, LIFT8-1399)
5. Lift8 – Default value for forced call changed to 30s to allow initialization of forced call according EN 81-28 in default setting (LIFT8-1388)
6. Lift8 LTE – Unreliable FW upgrade when LTE module inserted – fixed (LIFT8-801)
7. Lift8 LTE – Upgrade of module failed because of memory shortage – fixed (LIFT8-1333)

Version: 2.9.2 – Bugfix version

Final version: 2.9.2.0.5

Date: 17.3.2025

New features and improvements

1. Lift8 – Functionality of machine room communicator according EN 81-72, activation of microphone by button demanded (LIFT8-1014)
2. Lift8 LTE – possibility to set preferred DNS 1 and 2 added (LIFT8-1079)

Bugfixes

1. Lift8 – reporting identification od calling location in higher detail (LIFT8-449)
2. Lift8 LTE – long time period for SIM logging for some operators – fixed by longer timeout for critical operations (LIFT8-1081)
3. Control panel – Notification of license expiration of Lift8 server added, correct message when license expired displayed, login with expired license allowed with limited functionality (LIFT8-576, LIFT8-847, LIFT8-849, LIFT8-568, LIFT8-1232)
4. Communicator – limits for setting of port numbers replaced (LIFT8-523)
5. Lift8 server – Expiration of license correctly reported (LIFT8-868, LIFT8-1034)

Version: 2.9.0 – Evacuation scenario support, control center capacity increase

Final version: 2.9.0.0.2

Date: 6.12.2024

New features and improvements

1. Lift8 – evacuation mode available, up to 64 communication units, driven from connected IP phone – see manual for details (LIFT8-931, LIFT8-932, LIFT8-933, LIFT8-934, LIFT8-946, LIFT8-949, LIFT8-953, LIFT8-1036)
2. Lift8 – support of two Fireman units in one shaft available (LIFT8-1013)
3. Lift8 LTE – possibility to set PAP, CHAP authorization for wireless connection added (LIFT8-1052)
4. Control panel – counter of control and alarm call added (Lift8-776, Lift8-1038)
5. Lift8 server, communicator, control panel – improvements to increase number of connected devices up to 5000 units with keeping acceptable response for demanded operations (Lift8-350, Lift8-839, Lift8-865, Lift8-908)
6. Lift8 Control panel, Communicator – listing of information organized by groups in alphabetic order instead of time of recording – better orientation in listings (LIFT8-524)

Bugfixes

1. Control panel – increased number of control calls and reports to be registered to support traffic for higher number of connected devices (Lift8-882, Lift8-883).
2. Communicator – global map functionality switched off because of issues with map source and wrong function of displaying for 100+ points in map. Plam to solve this issue in future (LIFT8-843, LIFT8-1032).
3. Communicator – acceptation of identification number for incoming call with prefix * to be able to accept signaling from some SIP connection providers (LIFT8-708).
4. Communicator, Lift8 server – high number of registered control calls and alarm calls (about 50 000+) resulted into Lift8 server crash when higher amount of incoming calls occur concurrently (Lift8-883)

Version: 2.8.7 – 100 Mb LAN connection

Final version: 2.8.7.33.33

Date: 24.4.2024

New features and improvements

1. Lift8 – support for LAN communication board 100 Mb added (LIFT8-595, LIFT8-631)
2. Lift8 – second DNS server setting available (LIFT8-647, LIFT8-665)
3. Service tool - configurable space between DTMF tones during configuration to allow setting when issues with DTMF transmitting occur (LIFT8-677)
4. Service tool – changed provider of map source (LIFT8-734, LIFT8-701)
5. LiftIP1 – Incoming call by default configuration, ability to switch to voice menu by DTMF 9 (LIFT8-155)

Bugfixes

1. Lift8 – incorrect message about end of button stuck error when alarm activated – fixed (LIFT8-640, LIFT8-327)
2. Lift8 – error of wireless module registration fixed (LIFT8-745)
3. Lift8 LTE – MBN profile activation check after restart – improved reliability of VoLTE calls (LIFT8-676)
4. Lift8 LTE – upgrade of central unit blocked when SIM with PIN inserted and incorrect PIN set in Lift8 (LIFT8-667)
5. Lift8 LTE – change of SIP availability according to 2G/4G technology changes (LIFT8-675, LIFT8-753)
6. LIFT8 LTE – when LTE module inserted, upgrade from older versions which doesn’t support LTE module is not possible - fixed (LIFT8-683)
7. LIFT8 LTE – module restart after VoLTE activation on SIM – necessary for VoLTE activation (LIFT8-754)
8. Service tool – configuration blocked during loading to prevent data damage (LIFT8-662)
9. Service tool – visualization of line speed for LAN corrected after connecting device, no restart of lift8 needed (LIFT8-723)
10. Service tool – unsuccessful FW upgrade with LTE module thru USB (LIFT8-791)
11. Service tool – compatibility of different versions of service tool and L8-server allowed (LIFT8-569)
12. L8-Server – incorrect setting if SIP domain – used parameter from SIP server (LIFT8-795, LIF8-798)
13. L8-Server – incorrect length of CLIP (less then minimal length 5 digits) results in server restart – fixed (LIFT8-680)

     

     

    Version: 2.8.5 – LTE support

    Final version: 2.8.5.33.28

    Date: 27.11.2023

    New features and improvements

14. Lift8 - France language added to voice menu (LIFT8-527)
15. Lift8 – Support for LTE module integration and communication (LIFT8-110), (LIFT8-111), (LIFT8-112), (LIFT8-116), (LIFT8-121), (LIFT8-130), (LIFT8-137), (LIFT8-138), (LIFT8-140), (LIFT8-374)
16. Lift8 – SIP call using LTE module and wireless data connection implemented, direction of call defined by prefix (LIFT8-123), (LIFT8-124), (LIFT8-125), (LIFT8-114), (LIFT8-128), (LIFT8-134), (LIFT8-553), (LIFT8-634)
17. Lift8 – VoLTE call support using LTE module (LIFT8-117)
18. Lift8 – SMS services added to support LTE module (LIFT8-444)
19. Lift8 – Data connection support for LTE module (LIFT8-122)
20. Lift8 – Firmware in LTE module upgrade support (LIFT8-136)
21. Lift8 – LED functionality changed to support new features connected with LTE module use, description of new functionality in user manual (LIFT8-591)
22. Lift8 – Compressing of log files configured, block compressed when size 10MB reached (LIFT8-528)
23. Lift8 – Reporting of LTE module FW version, both the application FW and module FW, adding to log (LIFT8-582), (LIFT8-587)
24. Lift8 – Restart of LTE module when the malfunction detected, including logging of this situation with details allowing troubleshooting (LIFT8-108)
25. Service tool – SIP and VoLTE status visualization when LTE module assembled (LIFT8-435), (LIFT8-543)
26. Service tool – Reset for I/O module added to set default settings (LIFT8-359)
27. L8-Server – Repeating unsuccessful registration attempt till restart of application fixed (LIFT8-337)

Bugfixes

1. Lift8 - Change in checking call DTMF timing, unwanted space fixed (LIFT8-445)
2. Lift8 – Incorrect DTMF signaling during alarm call fixed, timing of signals for call end changed (LIFT8-446)
3. Lift8 – Watchdog for SIP connection on Ethernet port added, restart of SIP engine when registration failed (LIFT8-424), (LIFT8-309)
4. Lift8 – Day of week for checking call functionality fixed (LIFT8-251)
5. Lift8 – Default time setting from programming tool by DTMF fixed (LIFT8-333)
6. Lift8 – Parameter ‘day of week’ (986) shifted, beginning of week now Monay (LIFT8-325)
7. Lift8 – Incorrect finishing of SIP checking call thru Ethernet connection (LIFT8-615)
8. Lift8 – Default battery expiration time changed from 3 years to 2 years, according standards (LIFT8-632)
9. Lift8 – When PIN for SIM is filled with incorrect value, the PIN is after restart repeated till SIM blocked and PUK needed, now blocking of SIM avoided and wrong PIN indicated by LED (LIFT8-635)
10. Service tool – Beep notification of I/O module, input and output divided (LIFT8-330)
11. Service tool – Popup notification of I/O module status can result in application crash, fixed (LIFT8-425)
12. Service tool – Filtering of connection status fixed (LIFT8-464)
13. Service tool – Connection attempt during device factory reset results in impossibility of later connection, fixed (LIFT8-439)
14. Communicator – error in compatibility of database resulting to impossibility to save time setting fixed (LIFT8-511)
15. Communicator – change in PJSIP licensing done because of different mode of use (LIFT8-418)
16. Communicator - License politics error fixed, real status of license displayed (LIFT8-522)
17. Control panel – Incorrect export of Operational Calls report – format error fixed (LIFT8-410), (LIFT8-411)
18. Control panel – Export of alarm call identification file corrected (LIFT8-430)
19. Control panel – Incorrect way for new group creation by superuser in another group fixed (LIFT8-381)
20. Control panel – License politics error fixed, group licenses working after expiration (LIFT8-520), (LIFT8-517), (LIFT8-518)
21. Control panel – Communication with Lift8 during the call may result in application crash, fixed (LIFT8-611)
22. Graphic of tools – Resolution of application window setting changed (LIFT8-513)
23. All tools – After replacing from computer some empty directories resists, fixed (LIFT8-536)
24. Whole system – 2N logo changed (LIFT8-419)

Version: 2.8.4 - Schmitt

Final version: 2.8.4.33.21

Date: 15.5.2023

New features and improvements

1. Change in licensing – control of connected devices, whether the amount agrees with license, timing of trial time period improved (LIFT8-438), (LIFT-486)
2. E-mail notification of exceeding number of licenses added (LIFT8-488)

Bugfixes

1. Fixed errors in German translation for service tool (LIFT8-458)

Version: 2.8.4

Final version: 2.8.4.33.18

Date: 19.12.2022

New features and improvements

1. Web address changed from www.2n.cz to www.2n.com (LIFT8-377)
2. Lift8 - Voice menu for Spain added (LIFT8-365)
3. Lift8 - Voice menu for Latin America (Spain) added (LIFT8-366)
4. Service tool – Fixed position of parameter groups, independently on languages (LIFT8-375)
5. L8 server - Support of LiftIP2 on Lift8 server (LIFT8-326)
6. Communicator - Dual audio output added – different audio output can be set for ringing and for call, improved management of connected audio devices (LIFT8-396)
7. Control Panel – Increased maximal length of intercom name from 15 to 49 characters
8. Control Panel – Specific response (Custom) to Lift8 to confirm Checking call, Alarm call and Call to Lift8 added (LIFT8-393, LIFT8-394)

Bugfixes

1. Fixed translation in tool texts and hints (LIFT8-373, LIFT8-200, LIFT8-372)
2. Fixed issues in manuals and in references to manual in tools (LIFT8-334, LIFT8-335)
3. Lift8, LiftIP – Support of SIP proxy registration after change in Netstar (LIFT8-391, LIFT8-405)
4. Service tool - Wrong functionality of calendar, when month changed, day of weeks stays from last month (LIFT8-328)
5. LiftIP – Checking call timeout can result to incorrect end of call when registration during the waiting changes (LIFT8-403)
6. LiftIP – Finding in logs improved, wrong function of help fixed (LIFT8-245)
7. Service tool - Selection of connection in service tool for LiftIP selects more than one connection (LIFT8-361)
8. Service tool – Hidden keyword for parameter 1122 – keyword for RTSP connection to camera in service tool (LIFT8-305)
9. Service tool – Improved search in logs, now is case sensitive (LIFT8-371)
10. Service tool – Graphical view to configuration fixed (LIFT8-380)
11. L8 Server – MapQuest API service change supported to keep map functionality unchanged (LIFT8-388)
12. L8 Server – Setting detail of server fixed (LIFT8-515)
13. Communicator - During incoming call to Communicator, the map is not visible (LIFT8-347)
14. Communicator – Wrong position of intercom position on map, when windows size changed, improved accuracy of position (LIFT8-316, LIFT8-329, LIFT8-360)
15. Communicator – Incorrect setting of audio device for input and output (LIFT8-397)
16. Communicator – Incorrect displaying of names of audio devices – 32 characters only (LIFT8-398)
17. Communicator – Adding new Lift8 fails in specific circumstances (LIFT8-401)
18. Control Panel - List of intercoms in Control panel doesn’t show added intercom before refresh, not full view to all intercoms as admin without selected group of intercom (LIFT8-356)
19. Control Panel - Configuration of maps available to prevent issues connected with end of service MapQuest (LIFT8-363)
20. Control Panel - Fixed error in setting of test E-mail (LIFT8-302)
21. Control Panel – CPC Antenna 2N Extension support bug fixed (LIFT8-315)
22. Control Panel – Specific response to Lift8 to confirm Checking call, Alarm call and Call to Lift8 fixed (LIFT8-393, LIFT8-394)
23. Control Panel – ID extraction from CPC Antenna 2N ext. protocol fixed (LIFT8-357)
24. Control Panel – Export of alarm call has missing information about Agent, when the value is Server (LIFT8-343)
25. Control Panel – Export of call from intercom detail shows only test call (LIFT8-407)

Version: 2.8.3

Final version: 2.8.3.33.14

Date: 28.6.2022

New features and improvements

1. Lift8 – Identification of lift shaft in alarm call by voice message. (Lift8-25)
2. Lift8 – Alarm button self-test added, special type of alarm button needed. (Lift8-27, LIFT8-209)
3. Lift8 – Italian voice menu added. (LIFT8-31)
4. Lift8 – Polish voice menu added. (LIFT8-185)
5. Lift8 - Possibility to set siren output on the machine room communicator when alarm call activated. (LIFT8-33)
6. Lift8 - Information E-mail from alarm call to Control Panel (additional functionality to E-mail notification about checking call). (LIFT8-12)
7. LiftIP – Italian voice menu added. (LIFT8-32)
8. All tools - GUI of Lift8 supports seven languages: CZE, ENG, ESP, GER, FRA, ITA, RU. (LIFT8-6)
9. Communicator - Plan or map of the area with marked locality of lift is visible during emergency call. (LIFT8-7)
10. Communicator - Possibility to set keyboard shortcuts for define actions in Communicator to allow use of keyboard emulator. (LIFT8-20)
11. Communicator – Test of microphone connection added. (Lift8-189)

Bugfixes

1. Installation - Missing DLL libraries when Lift8 tools installed, mostly connected with Win10. (LIFT8-59, LIFT8-89)
2. Lift8 - Time overflow error – when Lift8 runs 49,7 days, timer overflow can result into unexpected irregularities in function. (LIFT8-36)
3. Lift8 – Alarm call with CPC Antena support failed in intercom identification – first number lost. (LIFT8-197)
4. Lift8 - Time synchronization by SNTP on by default – log with correct timing supported. (LIFT8-56)
5. LiftIP – issue with Payload Type for DTMF. (LIFT8-159, LIFT8-19)
6. LiftIP – communication issue with AVAYA – too long packets. (LIFT8-42)
7. LiftIP – After change of configuration confirmed by password, wrong password reported. (LIFT8-254)
8. Service tool - doesn’t correctly display all parameters depending on screen resolution. (LIFT8-52, LIFT8-147)
9. Service tool – incorrect filter, only numbers applied. (LIFT8-257)
10. Service tool – Device info error when older device connected because of missing hwinfo. (LIFT8-249)
11. L8 Server - Special characters for example - !@#$% - can’t be used as part of the SIP password. (LIFT8-10)
12. L8 Server -after change of IP address on connected PC registration failure occur. (LIFT8-90)
13. L8 Server – Error occur when E-mail report sent to three or more address. (Lift8-344)
14. L8 Server – Empty E-mail address for notification results into application lock or sending error. (LIFT8-247, LIFT8-301)
15. Communicator - Deleting of Control panel user, who is registered in Communicator results In lock of the application. (LIFT8-24)
16. Communicator - crash when display resolution changes. (Lift8-146)
17. Communicator - direct call user is not correctly signed off after user delete performed. (LIFT8-148)
18. Communicator - doesn’t allow moving of map by scrollbar. (LIFT8-171)
19. Communicator – when size of map changed, the change is not permanent. (LIFT8-252)
20. Communicator - crash when display resolution changes. (Lift8-146)
21. Communicator - direct call user is not correctly signed off after user delete performed.
22. Communicator - doesn’t allow moving of map by scrollbar. (LIFT8-171)
23. Communicator – when size of map changed, the change is not permanent. (LIFT8-252)
24. Communicator - doesn’t allow moving of map by scrollbar. (LIFT8-171)
25. Communicator – when size of map changed, the change is not permanent. (LIFT8-252)
26. Communicator - doesn’t allow moving of map by scrollbar. (LIFT8-171)
27. Communicator – when size of map changed, the change is not permanent. (LIFT8-252)
28. Communicator – When filtering by length of call or agent used, application crashes. (LIFT8-313)
29. Control panel - When Call server is set, correct visualization of all details in graphics is not guaranteed. (LIFT8-47)
30. Control panel – forced save of storage setting before next step can be performed. (LIFT8-158)
31. Control panel – When more intercoms on one plan placed, it is not possible to remove any of them. (LIFT8-217)
32. Control Panel – Test of storge availability, if lost, warning generated. (LIFT8-223)
33. Control Panel – searching of intercom by address in map failed. (LIFT8-92)

Release notes Lift8 and LiftIP

Version: 2.9.2 – Bugfix version

New features and improvements

Bugfixes

Version: 2.9.0 – Evacuation scenario support, control center capacity increase

New features and improvements

Bugfixes

Release notes Lift8 and LiftIP

Version: 2.8.4

Final version: 2.8.4.33.18

Date: 19.12.2022

New features and improvements

Web address changed from www.2n.cz to www.2n.com Lift8 - Voice menu for Spain added Lift8 - Voice menu for Latin America (Spain) added Service tool – Fixed position of parameter groups, independently on languages L8 server - Support of LiftIP2 on Lift8 server Communicator - Dual audio output added – different audio output can be set for ringing and for call, improved management of connected audio devices Control Panel – Increased maximal length of intercom name from 15 to 49 characters Control Panel – Specific response (Custom) to Lift8 to confirm Checking call, Alarm call and Call to Lift8 added

Bugfixes

Fixed translation in tool texts and hints Fixed issues in manuals and in references to manual in tools Lift8, LiftIP – Support of SIP proxy registration after change in Netstar Service tool - Wrong functionality of calendar, when month changed, day of weeks stays from last month LiftIP – Checking call timeout can result to incorrect end of call when registration during the waiting changes LiftIP – Finding in logs improved, wrong function of help fixed Service tool - Selection of connection in service tool for LiftIP selects more than one connection Service tool – Hidden keyword for parameter 1122 – keyword for RTSP connection to camera in service tool Service tool – Improved search in logs, now is case sensitive Service tool – Graphical view to configuration fixed L8 Server – MapQuest API service change supported to keep map functionality unchanged Communicator - During incoming call to Communicator, the map is not visible Communicator – Wrong position of intercom position on map, when windows size changed, improved accuracy of position Communicator – Incorrect setting of audio device for input and output Communicator – Incorrect displaying of names of audio devices – 32 characters only Communicator – Adding new Lift8 fails in specific circumstances Control Panel - List of intercoms in Control panel doesn’t show added intercom before refresh, not full view to all intercoms as admin without selected group of intercom Control Panel - Configuration of maps available to prevent issues connected with end of service MapQuest Control Panel - Fixed error in setting of test E-mail Control Panel – CPC Antenna 2N Extension support bug fixed Control Panel – Specific response to Lift8 to confirm Checking call, Alarm call and Call to Lift8 fixed Control Panel – ID extraction from CPC Antenna 2N ext. protocol fixed Control Panel – Export of alarm call has missing information about Agent, when the value is Server Control Panel – Export of call from intercom detail shows only test call

Version: 2.8.3

Final version: 2.8.3.33.14

Date: 28.6.2022

New features and improvements

Lift8 – Identification of lift shaft in alarm call by voice message. Lift8 – Alarm button self-test added, special type of alarm button needed. Lift8 – Italian voice menu added. Lift8 – Polish voice menu added. Lift8 - Possibility to set siren output on the machine room communicator when alarm call activated. Lift8 - Information E-mail from alarm call to Control Panel (additional functionality to E-mail notification about checking call). LiftIP – Italian voice menu added. All tools - GUI of Lift8 supports seven languages: CZE, ENG, ESP, GER, FRA, ITA, RU. Communicator - Plan or map of the area with marked locality of lift is visible during emergency call. Communicator - Possibility to set keyboard shortcuts for define actions in Communicator to allow use of keyboard emulator. Communicator – Test of microphone connection added.

Bugfixes

Installation - Missing DLL libraries when Lift8 tools installed, mostly connected with Win10. Lift8 - Time overflow error – when Lift8 runs 49,7 days, timer overflow can result into unexpected irregularities in function. Lift8 – Alarm call with CPC Antena support failed in intercom identification – first number lost. Lift8 - Time synchronization by SNTP on by default – log with correct timing supported. LiftIP – issue with Payload Type for DTMF. LiftIP – communication issue with AVAYA – too long packets. LiftIP – After change of configuration confirmed by password, wrong password reported. Service tool - doesn’t correctly display all parameters depending on screen resolution. Service tool – incorrect filter, only numbers applied. Service tool – Device info error when older device connected because of missing hwinfo. L8 Server - Special characters for example - !@#$% - can’t be used as part of the SIP password. L8 Server -  after change of IP address on connected PC registration failure occur. L8 Server – Error occur when E-mail report sent to three or more address. L8 Server – Empty E-mail address for notification results into application lock or sending error. Communicator - Deleting of Control panel user, who is registered in Communicator results In lock of the application. Communicator - crash when display resolution changes. Communicator - direct call user is not correctly signed off after user delete performed. Communicator - doesn’t allow moving of map by scrollbar. Communicator – when size of map changed, the change is not permanent. Communicator - crash when display resolution changes. Communicator - direct call user is not correctly signed off after user delete performed. Communicator - doesn’t allow moving of map by scrollbar. Communicator – when size of map changed, the change is not permanent. Communicator - doesn’t allow moving of map by scrollbar. Communicator – when size of map changed, the change is not permanent. Communicator - doesn’t allow moving of map by scrollbar. Communicator – when size of map changed, the change is not permanent. Communicator – When filtering by length of call or agent used, application crashes. Control panel - When Call server is set, correct visualization of all details in graphics is not guaranteed. Control panel – forced save of storage setting before next step can be performed. Control panel – When more intercoms on one plan placed, it is not possible to remove any of them. Control Panel – Test of storge availability, if lost, warning generated. Control Panel – searching of intercom by address in map failed.

Release notes Lift8 and LiftIP

Version: 2.8.7 – 100 Mb LAN connection

Final version: 2.8.7.33.34

Date: 1.7.2024

New features and improvements

Lift8 – support for LAN communication board 100 Mb added Lift8 – second DNS server setting available Service tool - configurable space between DTMF tones during configuration to allow setting when issues with DTMF transmitting occur Service tool – changed provider of map source LiftIP1 – Incoming call by default configuration, ability to switch to voice menu by DTMF 9

Bugfixes

Lift8 – incorrect message about end of button stuck error when alarm activated – fixed Lift8 – error of wireless module registration fixed Lift8 LTE – MBN profile activation check after restart – improved reliability of VoLTE calls Lift8 LTE – upgrade of central unit blocked when SIM with PIN inserted and incorrect PIN set in Lift8 Lift8 LTE – change of SIP availability according to 2G/4G technology changes LIFT8 LTE – when LTE module inserted, upgrade from older versions which doesn’t support LTE module is not possible - fixed LIFT8 LTE – module restart after VoLTE activation on SIM – necessary for VoLTE activation Service tool – configuration blocked during loading to prevent data damage Service tool – visualization of line speed for LAN corrected after connecting device, no restart of lift8 needed Service tool – unsuccessful FW upgrade with LTE module thru USB Service tool – compatibility of different versions of service tool and L8-server allowed L8-Server – incorrect setting if SIP domain – used parameter from SIP server L8-Server – incorrect length of CLIP (less then minimal length 5 digits) results in server restart – fixed

Version: 2.8.5 – LTE support

Final version: 2.8.5.33.28

Date: 27.11.2023

New features and improvements

Lift8 - France language added to voice menu Lift8 – Support for LTE module integration and communication Lift8 – SIP call using LTE module and wireless data connection implemented, direction of call defined by prefix Lift8 – VoLTE call support using LTE module Lift8 – SMS services added to support LTE module Lift8 – Data connection support for LTE module Lift8 – Firmware in LTE module upgrade support Lift8 – LED functionality changed to support new features connected with LTE module use, description of new functionality in user manual Lift8 – Compressing of log files configured, block compressed when size 10MB reached Lift8 – Reporting of LTE module FW version, both the application FW and module FW, adding to log Lift8 – Restart of LTE module when the malfunction detected, including logging of this situation with details allowing troubleshooting Service tool – SIP and VoLTE status visualization when LTE module assembled Service tool – Reset for I/O module added to set default settings L8-Server – Repeating unsuccessful registration attempt till restart of application fixed

Bugfixes

Lift8 - Change in checking call DTMF timing, unwanted space fixed Lift8 – Incorrect DTMF signaling during alarm call fixed, timing of signals for call end changed Lift8 – Watchdog for SIP connection on Ethernet port added, restart of SIP engine when registration failed Lift8 – Day of week for checking call functionality fixed Lift8 – Default time setting from programming tool by DTMF fixed Lift8 – Parameter ‘day of week’ (986) shifted, beginning of week now Monday Lift8 – Incorrect finishing of SIP checking call thru Ethernet connection Lift8 – Default battery expiration time changed from 3 years to 2 years, according standards Lift8 – When PIN for SIM is filled with incorrect value, the PIN is after restart repeated till SIM blocked and PUK needed, now blocking of SIM avoided and wrong PIN indicated by LED Service tool – Beep notification of I/O module, input and output divided Service tool – Popup notification of I/O module status can result in application crash, fixed Service tool – Filtering of connection status fixed Service tool – Connection attempt during device factory reset results in impossibility of later connection, fixed Communicator – error in compatibility of database resulting to impossibility to save time setting fixed Communicator – change in PJSIP licensing done because of different mode of use Communicator - License politics error fixed, real status of license displayed Control panel – Incorrect export of Operational Calls report – format error fixed Control panel – Export of alarm call identification file corrected Control panel – Incorrect way for new group creation by superuser in another group fixed Control panel – License politics error fixed, group licenses working after expiration Control panel – Communication with Lift8 during the call may result in application crash, fixed Graphic of tools – Resolution of application window setting changed All tools – After replacing from computer some empty directories resists, fixed Whole system – 2N logo changed

Version: 2.8.4

Final version: 2.8.4.33.21

Date: 15.5.2023

New features and improvements

Change in licensing – control of connected devices, whether the amount agrees with license, timing of trial time period improved E-mail notification of exceeding number of licenses added

Bugfixes

Fixed errors in German translation for service tool

Version: 2.8.4

Final version: 2.8.4.33.18

Date: 19.12.2022

New features and improvements

Web address changed from www.2n.cz to www.2n.com Lift8 - Voice menu for Spain added Lift8 - Voice menu for Latin America (Spain) added Service tool – Fixed position of parameter groups, independently on languages L8 server - Support of LiftIP2 on Lift8 server Communicator - Dual audio output added – different audio output can be set for ringing and for call, improved management of connected audio devices Control Panel – Increased maximal length of intercom name from 15 to 49 characters Control Panel – Specific response (Custom) to Lift8 to confirm Checking call, Alarm call and Call to Lift8 added

Bugfixes

Fixed translation in tool texts and hints Fixed issues in manuals and in references to manual in tools Lift8, LiftIP – Support of SIP proxy registration after change in Netstar Service tool - Wrong functionality of calendar, when month changed, day of weeks stays from last month LiftIP – Checking call timeout can result to incorrect end of call when registration during the waiting changes LiftIP – Finding in logs improved, wrong function of help fixed Service tool - Selection of connection in service tool for LiftIP selects more than one connection Service tool – Hidden keyword for parameter 1122 – keyword for RTSP connection to camera in service tool Service tool – Improved search in logs, now is case sensitive Service tool – Graphical view to configuration fixed L8 Server – MapQuest API service change supported to keep map functionality unchanged L8 Server – Setting detail of server fixed Communicator - During incoming call to Communicator, the map is not visible Communicator – Wrong position of intercom position on map, when windows size changed, improved accuracy of position Communicator – Incorrect setting of audio device for input and output Communicator – Incorrect displaying of names of audio devices – 32 characters only Communicator – Adding new Lift8 fails in specific circumstances Control Panel - List of intercoms in Control panel doesn’t show added intercom before refresh, not full view to all intercoms as admin without selected group of intercom Control Panel - Configuration of maps available to prevent issues connected with end of service MapQuest Control Panel - Fixed error in setting of test E-mail Control Panel – CPC Antenna 2N Extension support bug fixed Control Panel – Specific response to Lift8 to confirm Checking call, Alarm call and Call to Lift8 fixed Control Panel – ID extraction from CPC Antenna 2N ext. protocol fixed Control Panel – Export of alarm call has missing information about Agent, when the value is Server Control Panel – Export of call from intercom detail shows only test call

Version: 2.8.3

Final version: 2.8.3.33.14

Date: 28.6.2022

New features and improvements

Lift8 – Identification of lift shaft in alarm call by voice message Lift8 – Alarm button self-test added, special type of alarm button needed Lift8 – Italian voice menu added Lift8 – Polish voice menu added Lift8 - Possibility to set siren output on the machine room communicator when alarm call activated Lift8 - Information E-mail from alarm call to Control Panel (additional functionality to E-mail notification about checking call) LiftIP – Italian voice menu added All tools - GUI of Lift8 supports seven languages: CZE, ENG, ESP, GER, FRA, ITA, RU Communicator - Plan or map of the area with marked locality of lift is visible during emergency call Communicator - Possibility to set keyboard shortcuts for define actions in Communicator to allow use of keyboard emulator Communicator – Test of microphone connection added

Bugfixes

Installation - Missing DLL libraries when Lift8 tools installed, mostly connected with Win10 Lift8 - Time overflow error – when Lift8 runs 49,7 days, timer overflow can result into unexpected irregularities in function. Lift8 – Alarm call with CPC Antena support failed in intercom identification – first number lost Lift8 - Time synchronization by SNTP on by default – log with correct timing supported LiftIP – issue with Payload Type for DTMF LiftIP – communication issue with AVAYA – too long packets LiftIP – After change of configuration confirmed by password, wrong password reported Service tool - doesn’t correctly display all parameters depending on screen resolution Service tool – incorrect filter, only numbers applied Service tool – Device info error when older device connected because of missing hw info L8 Server - Special characters for example - !@#$% - can’t be used as part of the SIP password L8 Server -  after change of IP address on connected PC registration failure occur L8 Server – Error occur when E-mail report sent to three or more address L8 Server – Empty E-mail address for notification results into application lock or sending error Communicator - Deleting of Control panel user, who is registered in Communicator results In lock of the application Communicator - crash when display resolution changes Communicator - direct call user is not correctly signed off after user delete performed Communicator - doesn’t allow moving of map by scrollbar Communicator – when size of map changed, the change is not permanent Communicator - crash when display resolution changes Communicator - direct call user is not correctly signed off after user delete performed. Communicator - doesn’t allow moving of map by scrollbar Communicator – when size of map changed, the change is not permanent Communicator - doesn’t allow moving of map by scrollbar Communicator – when size of map changed, the change is not permanent Communicator - doesn’t allow moving of map by scrollbar Communicator – when size of map changed, the change is not permanent Communicator – When filtering by length of call or agent used, application crashes Control panel - When Call server is set, correct visualization of all details in graphics is not guaranteed Control panel – forced save of storage setting before next step can be performed Control panel – When more intercoms on one plan placed, it is not possible to remove any of them Control Panel – Test of storge availability, if lost, warning generated Control Panel – searching of intercom by address in map failed

Release notes Lift8 and LiftIP

Version: 2.8.7 – 100 Mb LAN connection

Final version: 2.8.7.33.34

Date: 1.7.2024

New features and improvements

Lift8 – support for LAN communication board 100 Mb added Lift8 – second DNS server setting available Service tool - configurable space between DTMF tones during configuration to allow setting when issues with DTMF transmitting occur Service tool – changed provider of map source LiftIP1 – Incoming call by default configuration, ability to switch to voice menu by DTMF 9

Bugfixes

Lift8 – incorrect message about end of button stuck error when alarm activated – fixed Lift8 – error of wireless module registration fixed Lift8 LTE – MBN profile activation check after restart – improved reliability of VoLTE calls Lift8 LTE – upgrade of central unit blocked when SIM with PIN inserted and incorrect PIN set in Lift8 Lift8 LTE – change of SIP availability according to 2G/4G technology changes LIFT8 LTE – when LTE module inserted, upgrade from older versions which doesn’t support LTE module is not possible - fixed LIFT8 LTE – module restart after VoLTE activation on SIM – necessary for VoLTE activation Service tool – configuration blocked during loading to prevent data damage Service tool – visualization of line speed for LAN corrected after connecting device, no restart of lift8 needed Service tool – unsuccessful FW upgrade with LTE module thru USB Service tool – compatibility of different versions of service tool and L8-server allowed L8-Server – incorrect setting if SIP domain – used parameter from SIP server L8-Server – incorrect length of CLIP (less then minimal length 5 digits) results in server restart – fixed

Version: 2.8.5 – LTE support

Final version: 2.8.5.33.28

Date: 27.11.2023

New features and improvements

Lift8 - France language added to voice menu Lift8 – Support for LTE module integration and communication Lift8 – SIP call using LTE module and wireless data connection implemented, direction of call defined by prefix Lift8 – VoLTE call support using LTE module Lift8 – SMS services added to support LTE module Lift8 – Data connection support for LTE module Lift8 – Firmware in LTE module upgrade support Lift8 – LED functionality changed to support new features connected with LTE module use, description of new functionality in user manual Lift8 – Compressing of log files configured, block compressed when size 10MB reached Lift8 – Reporting of LTE module FW version, both the application FW and module FW, adding to log Lift8 – Restart of LTE module when the malfunction detected, including logging of this situation with details allowing troubleshooting Service tool – SIP and VoLTE status visualization when LTE module assembled Service tool – Reset for I/O module added to set default settings L8-Server – Repeating unsuccessful registration attempt till restart of application fixed

Bugfixes

Lift8 - Change in checking call DTMF timing, unwanted space fixed Lift8 – Incorrect DTMF signaling during alarm call fixed, timing of signals for call end changed Lift8 – Watchdog for SIP connection on Ethernet port added, restart of SIP engine when registration failed Lift8 – Day of week for checking call functionality fixed Lift8 – Default time setting from programming tool by DTMF fixed Lift8 – Parameter ‘day of week’ (986) shifted, beginning of week now Monday Lift8 – Incorrect finishing of SIP checking call thru Ethernet connection Lift8 – Default battery expiration time changed from 3 years to 2 years, according standards Lift8 – When PIN for SIM is filled with incorrect value, the PIN is after restart repeated till SIM blocked and PUK needed, now blocking of SIM avoided and wrong PIN indicated by LED Service tool – Beep notification of I/O module, input and output divided Service tool – Popup notification of I/O module status can result in application crash, fixed Service tool – Filtering of connection status fixed Service tool – Connection attempt during device factory reset results in impossibility of later connection, fixed Communicator – error in compatibility of database resulting to impossibility to save time setting fixed Communicator – change in PJSIP licensing done because of different mode of use Communicator - License politics error fixed, real status of license displayed Control panel – Incorrect export of Operational Calls report – format error fixed Control panel – Export of alarm call identification file corrected Control panel – Incorrect way for new group creation by superuser in another group fixed Control panel – License politics error fixed, group licenses working after expiration Control panel – Communication with Lift8 during the call may result in application crash, fixed Graphic of tools – Resolution of application window setting changed All tools – After replacing from computer some empty directories resists, fixed Whole system – 2N logo changed

Version: 2.8.4

Final version: 2.8.4.33.21

Date: 15.5.2023

New features and improvements

Change in licensing – control of connected devices, whether the amount agrees with license, timing of trial time period improved E-mail notification of exceeding number of licenses added

Bugfixes

Fixed errors in German translation for service tool

Version: 2.8.4

Final version: 2.8.4.33.18

Date: 19.12.2022

New features and improvements

Web address changed from www.2n.cz to www.2n.com Lift8 - Voice menu for Spain added Lift8 - Voice menu for Latin America (Spain) added Service tool – Fixed position of parameter groups, independently on languages L8 server - Support of LiftIP2 on Lift8 server Communicator - Dual audio output added – different audio output can be set for ringing and for call, improved management of connected audio devices Control Panel – Increased maximal length of intercom name from 15 to 49 characters Control Panel – Specific response (Custom) to Lift8 to confirm Checking call, Alarm call and Call to Lift8 added

Bugfixes

Fixed translation in tool texts and hints Fixed issues in manuals and in references to manual in tools Lift8, LiftIP – Support of SIP proxy registration after change in Netstar Service tool - Wrong functionality of calendar, when month changed, day of weeks stays from last month LiftIP – Checking call timeout can result to incorrect end of call when registration during the waiting changes LiftIP – Finding in logs improved, wrong function of help fixed Service tool - Selection of connection in service tool for LiftIP selects more than one connection Service tool – Hidden keyword for parameter 1122 – keyword for RTSP connection to camera in service tool Service tool – Improved search in logs, now is case sensitive Service tool – Graphical view to configuration fixed L8 Server – MapQuest API service change supported to keep map functionality unchanged L8 Server – Setting detail of server fixed Communicator - During incoming call to Communicator, the map is not visible Communicator – Wrong position of intercom position on map, when windows size changed, improved accuracy of position Communicator – Incorrect setting of audio device for input and output Communicator – Incorrect displaying of names of audio devices – 32 characters only Communicator – Adding new Lift8 fails in specific circumstances Control Panel - List of intercoms in Control panel doesn’t show added intercom before refresh, not full view to all intercoms as admin without selected group of intercom Control Panel - Configuration of maps available to prevent issues connected with end of service MapQuest Control Panel - Fixed error in setting of test E-mail Control Panel – CPC Antenna 2N Extension support bug fixed Control Panel – Specific response to Lift8 to confirm Checking call, Alarm call and Call to Lift8 fixed Control Panel – ID extraction from CPC Antenna 2N ext. protocol fixed Control Panel – Export of alarm call has missing information about Agent, when the value is Server Control Panel – Export of call from intercom detail shows only test call

Version: 2.8.3

Final version: 2.8.3.33.14

Date: 28.6.2022

New features and improvements

Lift8 – Identification of lift shaft in alarm call by voice message Lift8 – Alarm button self-test added, special type of alarm button needed Lift8 – Italian voice menu added Lift8 – Polish voice menu added Lift8 - Possibility to set siren output on the machine room communicator when alarm call activated Lift8 - Information E-mail from alarm call to Control Panel (additional functionality to E-mail notification about checking call) LiftIP – Italian voice menu added All tools - GUI of Lift8 supports seven languages: CZE, ENG, ESP, GER, FRA, ITA, RU Communicator - Plan or map of the area with marked locality of lift is visible during emergency call Communicator - Possibility to set keyboard shortcuts for define actions in Communicator to allow use of keyboard emulator Communicator – Test of microphone connection added

Bugfixes

Installation - Missing DLL libraries when Lift8 tools installed, mostly connected with Win10 Lift8 - Time overflow error – when Lift8 runs 49,7 days, timer overflow can result into unexpected irregularities in function. Lift8 – Alarm call with CPC Antena support failed in intercom identification – first number lost Lift8 - Time synchronization by SNTP on by default – log with correct timing supported LiftIP – issue with Payload Type for DTMF LiftIP – communication issue with AVAYA – too long packets LiftIP – After change of configuration confirmed by password, wrong password reported Service tool - doesn’t correctly display all parameters depending on screen resolution Service tool – incorrect filter, only numbers applied Service tool – Device info error when older device connected because of missing hw info L8 Server - Special characters for example - !@#$% - can’t be used as part of the SIP password L8 Server -  after change of IP address on connected PC registration failure occur L8 Server – Error occur when E-mail report sent to three or more address L8 Server – Empty E-mail address for notification results into application lock or sending error Communicator - Deleting of Control panel user, who is registered in Communicator results In lock of the application Communicator - crash when display resolution changes Communicator - direct call user is not correctly signed off after user delete performed Communicator - doesn’t allow moving of map by scrollbar Communicator – when size of map changed, the change is not permanent Communicator - crash when display resolution changes Communicator - direct call user is not correctly signed off after user delete performed. Communicator - doesn’t allow moving of map by scrollbar Communicator – when size of map changed, the change is not permanent Communicator - doesn’t allow moving of map by scrollbar Communicator – when size of map changed, the change is not permanent Communicator - doesn’t allow moving of map by scrollbar Communicator – when size of map changed, the change is not permanent Communicator – When filtering by length of call or agent used, application crashes Control panel - When Call server is set, correct visualization of all details in graphics is not guaranteed Control panel – forced save of storage setting before next step can be performed Control panel – When more intercoms on one plan placed, it is not possible to remove any of them Control Panel – Test of storge availability, if lost, warning generated Control Panel – searching of intercom by address in map failed

Release notes Lift8 and LiftIP

Version: 2.8.7 – 100 Mb LAN connection

Final version: 2.8.7.33.34

Date: 1.7.2024

New features and improvements

Lift8 – support for LAN communication board 100 Mb added Lift8 – second DNS server setting available Service tool - configurable space between DTMF tones during configuration to allow setting when issues with DTMF transmitting occur Service tool – changed provider of map source LiftIP1 – Incoming call by default configuration, ability to switch to voice menu by DTMF 9

Bugfixes

Lift8 – incorrect message about end of button stuck error when alarm activated – fixed Lift8 – error of wireless module registration fixed Lift8 LTE – MBN profile activation check after restart – improved reliability of VoLTE calls Lift8 LTE – upgrade of central unit blocked when SIM with PIN inserted and incorrect PIN set in Lift8 Lift8 LTE – change of SIP availability according to 2G/4G technology changes LIFT8 LTE – when LTE module inserted, upgrade from older versions which doesn’t support LTE module is not possible - fixed LIFT8 LTE – module restart after VoLTE activation on SIM – necessary for VoLTE activation Service tool – configuration blocked during loading to prevent data damage Service tool – visualization of line speed for LAN corrected after connecting device, no restart of lift8 needed Service tool – unsuccessful FW upgrade with LTE module thru USB Service tool – compatibility of different versions of service tool and L8-server allowed L8-Server – incorrect setting if SIP domain – used parameter from SIP server L8-Server – incorrect length of CLIP (less then minimal length 5 digits) results in server restart – fixed

Version: 2.8.5 – LTE support

Final version: 2.8.5.33.28

Date: 27.11.2023

New features and improvements

Lift8 - France language added to voice menu Lift8 – Support for LTE module integration and communication Lift8 – SIP call using LTE module and wireless data connection implemented, direction of call defined by prefix Lift8 – VoLTE call support using LTE module Lift8 – SMS services added to support LTE module Lift8 – Data connection support for LTE module Lift8 – Firmware in LTE module upgrade support Lift8 – LED functionality changed to support new features connected with LTE module use, description of new functionality in user manual Lift8 – Compressing of log files configured, block compressed when size 10MB reached Lift8 – Reporting of LTE module FW version, both the application FW and module FW, adding to log Lift8 – Restart of LTE module when the malfunction detected, including logging of this situation with details allowing troubleshooting Service tool – SIP and VoLTE status visualization when LTE module assembled Service tool – Reset for I/O module added to set default settings L8-Server – Repeating unsuccessful registration attempt till restart of application fixed

Bugfixes

Lift8 - Change in checking call DTMF timing, unwanted space fixed Lift8 – Incorrect DTMF signaling during alarm call fixed, timing of signals for call end changed Lift8 – Watchdog for SIP connection on Ethernet port added, restart of SIP engine when registration failed Lift8 – Day of week for checking call functionality fixed Lift8 – Default time setting from programming tool by DTMF fixed Lift8 – Parameter ‘day of week’ (986) shifted, beginning of week now Monday Lift8 – Incorrect finishing of SIP checking call thru Ethernet connection Lift8 – Default battery expiration time changed from 3 years to 2 years, according standards Lift8 – When PIN for SIM is filled with incorrect value, the PIN is after restart repeated till SIM blocked and PUK needed, now blocking of SIM avoided and wrong PIN indicated by LED Service tool – Beep notification of I/O module, input and output divided Service tool – Popup notification of I/O module status can result in application crash, fixed Service tool – Filtering of connection status fixed Service tool – Connection attempt during device factory reset results in impossibility of later connection, fixed Communicator – error in compatibility of database resulting to impossibility to save time setting fixed Communicator – change in PJSIP licensing done because of different mode of use Communicator - License politics error fixed, real status of license displayed Control panel – Incorrect export of Operational Calls report – format error fixed Control panel – Export of alarm call identification file corrected Control panel – Incorrect way for new group creation by superuser in another group fixed Control panel – License politics error fixed, group licenses working after expiration Control panel – Communication with Lift8 during the call may result in application crash, fixed Graphic of tools – Resolution of application window setting changed All tools – After replacing from computer some empty directories resists, fixed Whole system – 2N logo changed

Version: 2.8.4

Final version: 2.8.4.33.21

Date: 15.5.2023

New features and improvements

Change in licensing – control of connected devices, whether the amount agrees with license, timing of trial time period improved E-mail notification of exceeding number of licenses added

Bugfixes

Fixed errors in German translation for service tool

Version: 2.8.4

Final version: 2.8.4.33.18

Date: 19.12.2022

New features and improvements

Web address changed from www.2n.cz to www.2n.com Lift8 - Voice menu for Spain added Lift8 - Voice menu for Latin America (Spain) added Service tool – Fixed position of parameter groups, independently on languages L8 server - Support of LiftIP2 on Lift8 server Communicator - Dual audio output added – different audio output can be set for ringing and for call, improved management of connected audio devices Control Panel – Increased maximal length of intercom name from 15 to 49 characters Control Panel – Specific response (Custom) to Lift8 to confirm Checking call, Alarm call and Call to Lift8 added

Bugfixes

Fixed translation in tool texts and hints Fixed issues in manuals and in references to manual in tools Lift8, LiftIP – Support of SIP proxy registration after change in Netstar Service tool - Wrong functionality of calendar, when month changed, day of weeks stays from last month LiftIP – Checking call timeout can result to incorrect end of call when registration during the waiting changes LiftIP – Finding in logs improved, wrong function of help fixed Service tool - Selection of connection in service tool for LiftIP selects more than one connection Service tool – Hidden keyword for parameter 1122 – keyword for RTSP connection to camera in service tool Service tool – Improved search in logs, now is case sensitive Service tool – Graphical view to configuration fixed L8 Server – MapQuest API service change supported to keep map functionality unchanged L8 Server – Setting detail of server fixed Communicator - During incoming call to Communicator, the map is not visible Communicator – Wrong position of intercom position on map, when windows size changed, improved accuracy of position Communicator – Incorrect setting of audio device for input and output Communicator – Incorrect displaying of names of audio devices – 32 characters only Communicator – Adding new Lift8 fails in specific circumstances Control Panel - List of intercoms in Control panel doesn’t show added intercom before refresh, not full view to all intercoms as admin without selected group of intercom Control Panel - Configuration of maps available to prevent issues connected with end of service MapQuest Control Panel - Fixed error in setting of test E-mail Control Panel – CPC Antenna 2N Extension support bug fixed Control Panel – Specific response to Lift8 to confirm Checking call, Alarm call and Call to Lift8 fixed Control Panel – ID extraction from CPC Antenna 2N ext. protocol fixed Control Panel – Export of alarm call has missing information about Agent, when the value is Server Control Panel – Export of call from intercom detail shows only test call

Version: 2.8.3

Final version: 2.8.3.33.14

Date: 28.6.2022

New features and improvements

Lift8 – Identification of lift shaft in alarm call by voice message Lift8 – Alarm button self-test added, special type of alarm button needed Lift8 – Italian voice menu added Lift8 – Polish voice menu added Lift8 - Possibility to set siren output on the machine room communicator when alarm call activated Lift8 - Information E-mail from alarm call to Control Panel (additional functionality to E-mail notification about checking call) LiftIP – Italian voice menu added All tools - GUI of Lift8 supports seven languages: CZE, ENG, ESP, GER, FRA, ITA, RU Communicator - Plan or map of the area with marked locality of lift is visible during emergency call Communicator - Possibility to set keyboard shortcuts for define actions in Communicator to allow use of keyboard emulator Communicator – Test of microphone connection added

Bugfixes

Installation - Missing DLL libraries when Lift8 tools installed, mostly connected with Win10 Lift8 - Time overflow error – when Lift8 runs 49,7 days, timer overflow can result into unexpected irregularities in function. Lift8 – Alarm call with CPC Antena support failed in intercom identification – first number lost Lift8 - Time synchronization by SNTP on by default – log with correct timing supported LiftIP – issue with Payload Type for DTMF LiftIP – communication issue with AVAYA – too long packets LiftIP – After change of configuration confirmed by password, wrong password reported Service tool - doesn’t correctly display all parameters depending on screen resolution Service tool – incorrect filter, only numbers applied Service tool – Device info error when older device connected because of missing hw info L8 Server - Special characters for example - !@#$% - can’t be used as part of the SIP password L8 Server -  after change of IP address on connected PC registration failure occur L8 Server – Error occur when E-mail report sent to three or more address L8 Server – Empty E-mail address for notification results into application lock or sending error Communicator - Deleting of Control panel user, who is registered in Communicator results In lock of the application Communicator - crash when display resolution changes Communicator - direct call user is not correctly signed off after user delete performed Communicator - doesn’t allow moving of map by scrollbar Communicator – when size of map changed, the change is not permanent Communicator - crash when display resolution changes Communicator - direct call user is not correctly signed off after user delete performed. Communicator - doesn’t allow moving of map by scrollbar Communicator – when size of map changed, the change is not permanent Communicator - doesn’t allow moving of map by scrollbar Communicator – when size of map changed, the change is not permanent Communicator - doesn’t allow moving of map by scrollbar Communicator – when size of map changed, the change is not permanent Communicator – When filtering by length of call or agent used, application crashes Control panel - When Call server is set, correct visualization of all details in graphics is not guaranteed Control panel – forced save of storage setting before next step can be performed Control panel – When more intercoms on one plan placed, it is not possible to remove any of them Control Panel – Test of storge availability, if lost, warning generated Control Panel – searching of intercom by address in map failed