2N Fortis Commander - overview and how to use it

Since the Access Commander 3.5 version, it is possible to configure 2N Fortis Electronic locks with the 2N Fortis Commander software. A project file needs to be downloaded from the "Settings -> Electronic locks -> Fortis Commander" section of the 2N Access Commander. The 2N Fortis Commander software can be downloaded from the 2N Download Centre. The link is available in the "Settings -> Electronic locks -> Fortis Commander -> Download app" section of the Access Commander's web interface as well. Every action in the 2N Fortis Commander is saved automatically and does not need to be confirmed. Initial projects pageOpening a projectProject pageConnecting to a deviceConnected device detail page Actions pageEvents page Closing the project Initial projects page When running the 2N Fortis Commander, it is possible to see the File and Help options (1), Instructions for opening a project/configuration file (2) and Recently opened projects with details about the files (3). Opening a project To open a project, you can either open the project file, which was downloaded from the 2N Access Commander on your computer. Or you can click on the Open project button and navigate to the project file, which was downloaded from the 2N Access Commander. Either way, the 2N Fortis Commander will ask you for the password of the project file, which is set up in the "Settings -> Electronic locks -> Fortis Commander" section of the 2N Access Commander when downloading. Project page The project page contains the information of 2N Fortis devices assigned to the Electronic locks pre-configured in the 2N Access Commander. It is possible to search by a lock name (1), show/hide assigned doors (configured 2N Fortis devices) (2) and see the list of 2N Fortis devices (3). When a new project from the first initialisation of 2N Fortis in 2N Access Commander is opened, there are no assigned devices at first, and they are shown as not configured. Connecting to a device To connect to a 2N Fortis device, the computer running the 2N Fortis Commander needs to be equipped with Bluetooth. Click on the "Connect to device" button and swipe the Lock set up & Service card to the electronic lock to enable the pairing mode. The lights on the 2N Fortis Cylinder or Handle will be blinking with a blue light. Keep your computer close to the 2N Fortis Cylinder/Handle throughout the pairing process. Lock setup & Service cards can be created for your project in the Access Commander (Settings > Electronic Locks > Maintenance cards) section of the 2N Access Commander. During the pairing/connecting process, it is possible to cancel it as well. Once the 2N Fortis Commander connects to the 2N Fortis device, you will see the device's details. Connected device detail page Actions page When connected to a 2N Fortis electronic lock with the 2N Fortis Commander, it is possible to disconnect from the device and see a few sections: 1 - Disconnect from the device 2 - Device name (if device is already assigned and configured) and the device type (2N Fortis Cylinder or 2N Fortis Handle) 3 - Device status, its serial number and firmware version 4 - Actions and Events tab - the Actions tab is shown by default 5 - Assign lock section to to assign it to the device pre-configured in the 2N Access Commander 6 - Device Lock/Unlock options (Lock button also restore normal operation - after using Disassembly or Battery replacement buttons on 2N Fortis Cylinder) 7 - Disassembly option - available only for the 2N Fortis Cylinder to dismount the electronic lock 8 - Battery replacement option - available only for the 2N Fortis Cylinder, for removing the cylinder cover to replace the batteries 9 - Factory reset option - more information can be found in this FAQ article Events page Each time the 2N Fortis Commander connects to the 2N Fortis device, it automatically pulls the Events from the device. These events can be uploaded to the 2N Access Commander by uploading the 2N Fortis Commander project file back into the "Settings -> Electronic locks -> Fortis Commander" section of the 2N Access Commander's web interface. No changes to the 2N Fortis device are necessary. Only to connect to the device to pull out the Events. Closing the project After the changes have been made and the 2N Fortis Commander is disconnected from the devices, the information about the devices will be displayed. There is also a message display informing about the next step to upload the configuration to the 2N Access Commander. The 2N Fortis Commander project needs to be closed so the file can be uploaded to the 2N Access Commander in the "Settings -> Electronic locks -> Fortis Commander" section of the web interface. The project can be closed in the "File -> Close project section, and the view will be changed back to the Projects page. Finally, after closing the 2N Fortis Commander project, it is possible to see all the projects and their dates with the option to open them again, if necessary. When clicking on the file path of the 2N Fortis project file, the Windows file explorer is opened with the project file highlighted. The last step is to upload the edited 2N Fortis Commander project to the 2N Access Commander in the "Settings -> Electronic locks -> Fortis Commander" section.

2N Fortis - mechanical assembly and disassembly

This FAQ article describes the assembly and disassembly of the 2N Fortis Handle and Cylinder. 2N Fortis Handle General assembly instructionsAssemblyDisassemly 2N Fortis Cylinder General assembly instructionsAssemblyDisassembly 2N Fortis Handle General assembly instructions Check the approval when installing the 2N Fortis door handle in a fire/smoke-resistant door or in an escape doorIf a cylinder holder is present in the door, then it should be sealed properly, for e.g. using a dummy cylinder.Ensure that the latches or seals fitted to the door do not hinder the proper operation of the 2N Fortis Handle.Ensure that the door handle does not protrude and prevent the door from swinging freely.When installing the 2N Fortis Handle door handle in the circular rosette version, the hole in the door for inserting the handle pin should have a diameter of at least 25 mm. Before assembling the door handle, always check whether all the components can move freely. After assembly, check the function with the door open.The pre-tension in the mortise lock or the deviation of the horizontal basic position must not exceed 3°. If the deviation is greater, the electronic door handle cannot engage or disengage. Assembly The square pin has to be assembled before installation on the electronic door handle (outside). This applies to all the versions and is shown here using the circular rosette. 1 Electronic door handle2 Spiral clamping pin3 Square4 Adapter sleeve for square (only for 7 mm square) Insert the adapter sleeve into the square holder (if available) Insert the square onto the retaining pin and into the square holder Insert the spiral clamping pin into the square Insert the square pin of the electronic door handle into the square nut of the lock. Place the drilling template on the square pin, align horizontally and centre punch the hole markings. Remove the square pin again. Drill holes of diameter 8 - 8.5 mm at the marked positions. Do not drill into or through the lock casing. Insert the square pin of the electronic door handle once again into the square nut of the lock. If necessary, place the adapter sleeve supplied on the square pin. Insert the holder of the mechanical door handle from the other side and screw it along with the electronic door handle through the door panel. Use the supplied mounting screws. Insert the mechanical door handle, keeping it in a horizontal position. For door handles pointing to the right, tighten the rosette towards the left, guide it over the handle holder and engage the bayonet lock. Accordingly, tighten the rosette towards the right for door handles pointing to the left. Insert the locking screw from the bottom of the handle and tighten it. Check the functionality and easy movement of the door handle with the door open. The handle is already engaged when delivered. When engaged, the catch of the lock should be completely inside the lock casing when the latch is pressed down. To operate the door handle, insert the battery and close the housing (see FAQ Battery replacement). The electronic door handle disengages only after the battery is inserted. After holding up an authorised key for the first time, only the two upper LEDs light up as an indication. When inserting the battery, make sure that the handle is in its designated horizontal position. This is necessary for the orientation sensor to calibrate and the device to function correctly. Disassembly Remove the locking screw from the bottom of the handle and take off the handle. Remove the supplied mounting screws from the holder of the mechanical door handle and then the electronic door handle. 2N Fortis Cylinder General assembly instructions Before assembling the 2N Fortis cylinder in a fire/smoke-resistant door, please recheck the fire certification to ensure conformity.Ensure that the sealing affixed on the door does not hamper the proper operation of the product. Ensure that the 2N Fortis Cylinder projections do not obstruct the free swing of the door.As 2N Fortis Cylinders are supplied in a completely assembled state as standard, it may be necessary to perform the steps for disassembly, as described in Disassembly part of this FAQ article, before mounting.To activate the 2N Fortis Cylinder, insert the batteries or remove the battery tag, if present, and close the casing (see Battery replacement FAQ article)Before mounting the 2N Fortis Cylinder, always check that all components move freely.Carry out the assembly with the door open.Only for cylinders supplied as single components: During initial installation, put in 1 to 2 drops (max. 0.1 ml) of a non-resinous oil in the cylinder body. It should not be sprayed directly into the cylinder body with a spray can. Assembly Remove the fixing screw of the cylinder existing and dismantle the present cylinder. Push in the cylinder body and fasten with fixing screw. Tighten the fixing screw by hand, do not use a battery-operated screwdriver with a high torque. The cylinder body must not project outside its enclosing fitting by more than 1 to 3 mm, but it should also not be installed sunk in the upholstery. After inserting the battery (see Battery replacement FAQ article), use the Service card previously configured in the Access Commander (see FAQ) to set the 2N Fortis Cylinder to service state. The electronic cylinder is mounted into the cylinder casing by inserting and turning at the same time. Scan the previously configured service card again to "lock" the cylinder in place. Make sure that the knob cylinder operates easily and smoothly with the door open. Disassembly Use the Service card previously configured in the Access Commander (see FAQ) to set the 2N Fortis Cylinder to service state. The electronic cylinder can be removed from the cylinder casing by pulling and turning at the same time.

Factory reset - How to do factory reset for 2N Fortis devices

Since the Access Commander 3.5 version, it is possible to configure 2N Fortis Electronic locks with the 2N Fortis Commander software. The 2N Fortis Commander software can be downloaded from the 2N Download Centre. The link is available in the "Settings -> Electronic locks -> Fortis Commander -> Download app" section of the Access Commander's web interface as well. Using 2N Fortis Commander you can perform factory reset of the 2N Fortis Cylinder or 2N Fortis Handle. To do so, you need to have correct Lock setup & service card for the 2N Fortis device. Lock setup & service card can be created in Access Commander in Settings - Electronic locks - Maintenance cards. To program Lock setup & service card please make sure you have 2N USB driver installed and 2N External USB RFID reader connected. This card will have correct decryption keys which will allow it to enable bluetooth communication on programmed 2N Fortis devices. Once you have Lock setup & service card and 2N Fortis Commander ready, please follow next steps to reset each 2N Fortis device one by one. If not already present in 2N Fortis Commander, go to 2N Access Commander and protect the Fortis file by password (Settings - Electronic locks - Fortis Commander). Continue by downloading the file with information about 2N Fortis devices from 2N Access Commander (Settings - Electronic locks - Fortis Commander). Open downloaded file in 2N Fortis Commander (use the password to unlock the file in 2N Fortis Commander) Click Connect to device button Swipe Lock setup & service card over 2N Fortis device you want to reset. It shall start blinking blue. Please do just one 2N Fortis device at any given time.After 2N Fortis Commander connects to device, use Factory reset button to reset it. Disconnect from the device Please repeat the steps 3-6 for every device you want to reset to 2N factory default values.

Sizes of Spindle and Cylinder for project

In this FAQ article, we'll explain the details of spindles for 2N Fortis Handles and cylinder bodies for the 2N Fortis Cylinders. Door spindles for handles depend on door thickness, and cylinder bodies depend on the thickness of the door, including the thickness of the rossetes mounted. Spindle - what size do I need for my project? Spindle is the part which connects electronic handle with mechanical handle through the door. The length specified in the details of the spindle for each order number is the required door thickness and NOT the actual length of the spindle. In reality, the spindle is longer than the door thickness, so the handles can be fixed to the spindle from both sides of the door. When ordering a spindle, it is required to know the door thickness (B+A dimension as shown in the picture below). You also need to know how the spindle fits the hole between the handles (7mm, 8mm or 9mm). Where to measure the door thickness for spindle: For example, the Spindle with screws set, 8mm, 75 - 83mm (part no. 1120460883) is for an installation where the door thickness is between 75 - 83mm. Cylinder - What size do I need for my project? Cylinder body is the part which allows electronic cylinder and physical knob to fit to the door in the place where usually keys are inserted. To fit 2N Fortis Cylinder you need special Cylinder body designed to hold it. When ordering a Cylinder body, it is required to know the thickness of the door, including the thickness of the rossetes (or backplate) mounted to the door. The parameter specified in the details of the cylinder body is the required length. Cylinder bodies' length is specified by the OUT (B) and IN (A) sides' length. The OUT side is where the 2N Fortis Cylinder is mounted, and the IN side is where the mechanical knob is usually mounted. When calculating the dimension B+A as shown in the pictures below, make sure the total length of the 2N Cylinder body does not exceed the B+A dimension of the door (including rosette or backplate) for more than 3mm on both sides. Where to measure the B+A dimension for Cylinder body (when using rosettes): Where to measure the B+A dimension for Cylinder body (when using backplate): Please note that the rosette for the 2N Fortis Cylinder sold by 2N (order numbers 112047101 and 112047102) is 8mm thick. For custom rosettes or backplates installed on your door, you need to know its dimensions before you order the Cylinder body. For example, the Cylinder body 30/40 (part no. 11204313040) is 70mm long, where the OUT side is 30mm long, and the IN side is 40mm long. In case of using the 2N Fortis Cylinder on both sides, the minimum thickness of the door, including the thickness of the rossetes mounted, needs to be 70mm. You need to order the Cylinder body to match the dimensions.

Time profiles - managing time restricted access for 2N Fortis

Time profiles are supported for 2N Fortis in 2N Access Commander version 3.4 or newer. However some limitations apply. Time profiles in 2N Access Commander are an optional feature used to limit access for users to specific days and time periods.They can be assigned to access rules, which define the relationship between a group of users and a Zone (where devices are assigned).When 2N Fortis devices are part of that Zone, time profiles can also control when those devices are accessible. Limitations of time profiles for 2N Frotis: Time profiles are supported only in access rules, not directly on devices or users. Time profiles are saved on each programmed user card for 2N FortisEach 2N Fortis programmed user card can hold a maximum of 4 time intervals per day.If multiple 2N Fortis devices are involved, each can have its own set of up to 4 intervals per day. Example of data stored in card: DeviceDayAllowed Time IntervalsLock 1MondayINT1, INT2, INT3, INT4Lock 1MondayINT3, INT5Handle 6MondayINT1, INT6, INT4, INT8Handle 2TuesdayINT5, INT6, INT7, INT8 Merging of Time Profiles: If a user in 2N Access Commander is a member of multiple groups that use different time profiles for access to the same 2N Fortis device,Access Commander will merge the intervals and attempt to create a combined time profile (not visible to user).However, even after merging, the resulting time profile cannot exceed 4 intervals per day per 2N Fortis device the card has access to. Additional Notes: Access Commander will indicate whether a time profile is valid or invalid for 2N Fortis. Holiday settings are not supported for 2N Fortis compatible time profiles in 2N Access Commander.